Hi, I bought my Zanussi ZCV663MWC cooker ten years ago, I replaced the top element four months ago and its been fine until now. When I turn the top oven on it heats up then after ten minutes it trips the mains. Also I have never used the bottom oven but when I turned it on it also tripped the...
Some months ago the transformer feeding my road had a HV phase loss with the result that my house was only getting about 85V. It was interesting seeing what stuff worked and what didn't: for example, 60W bulbs glowed, fluorescent lights didn't(!), some LED lamps worked, others didn't, and my DAB...
Hi I wanted to run my car air con on a hook up at a camp site. Could I buy a mains hook up kit and run a charger to my vehicle battery. Would that work? I guess it would depend how much the charger is putting into the battery, what rating charger would I need.
Hello,
I’m boarding out my loft for storage and I’d like some decent lighting up there rather than loft lights I’m currently using.
I purchased some LED batten lights that my cousin, who is a qualified electrician, said he will come and wire in. He’s good at what he does, he’s sadly just lazy...
Hi guys I have been tasked with upgrading some old rewireable fuseboards for a food warehouse that runs continually 24/7. I was asked to do an EICR on the install as there maintenance guys were having issues with blowing fuses. Wiring issues are sorted now. These fuse boards are old asbestos...
Hi,
I'm new to the site and wanted to seek some advice thanks, relating to adding fused spurs to existing ring mains in a commercial premises.
Some of my other colleagues have been asked to explore ring main alterations, but they look after some site based kit and this is more related to...
Hi,
I was wondering if the wylex/Proteus SPD Isolators where dual isolator, they have 4 terminals at the bottom, can you use them to take 2 sets of tails of them.
And what size earth should be used for the SPD when using 25mm tails and Is connecting it in parallel to the main earth correct...
About 15 years ago, after having had a modern consumer unit fitted, and prompted by our electrician, I asked my then energy supplier (Tonik) if our 1968 60 Amp cut-out fuse could be upgraded to 100 Amps, and what additional work/expense would be needed.
I did not know that my request had gone...
Hi Guys,
Looking for some options to provide surge protection to a 100a TPN sub main to be wired 60m from the origin
Im currently looking at installing a 4 way TPN mccb panel board with spd at the origin but it looks as if its going to cost the best part of a grand
This is obviously a far...
Hi everyone
Just looking for a little advise on if my plan to run this spur is okay I’ve drawn a diagram in hopes to make my expiation simpler
The MS square is the main socket which has not been tampered with
The F is a 13 amp fuse spur
And the S are the additional sockets which I plan to...
convert 12v gu5.1 to mains gu10. but confused why this transformer has two live wires? can someone explain.Do I need a driver or I can directly attach GU10 holder to the mains? and what should be done with second live wires?
I want to use a manual change over switch to safely connect a 21kVA single phase tractor PTO powered generator to my mains supply in case of power outages. The cable run from the generator to the outside mains incoming box will be about 40 meters. I intend to use 16mm SWA for that run. The...
Here's a Sunday puzzler for you all.....
I've a large rental stock of properly made up mains adaptors for use in Europe and elsewhere - so typically something like a Schuko >1m 3c H05 / H07 1.5mm flex > twin 13A duraplug trailing socket, variants for other countries, USA and so on.
The other...
Hi,
What is th emaximum current draw allowable from the mains for...
UK domestic single phase
Light industrial single phase
Light industrial 3 phase
If there are different levels, then please advise.
Basically i suppose what i am asking is what current does the wiring have to be rated for...
Hi everyone, my husband has turned up on a job with a very old mains that he will need to shut down at some stage. Does anyone know the procedure for shutting down/re starting this type of mains? Photos attached. Apologies if this is the wrong forum and thanks for reading!
I currently have a Single Pole Double Throw switch with 5 pins (as shown below) which I want to wire up to UK mains:
┌─────┐
│ NC │
└─────┘
┌─────┐ ┌─────┐ ┌─────┐
│ - │ │ NO │ │ + │
└─────┘ └─────┘ └─────┘
┌─────┐
│ COM │
└─────┘...
This is a question with probably so many answers and solutions, but I wondered how people would do it.
I have a clients house which already has one submain on a 40A MCB to a Garage with a 20A RCBO radial and a 6A RCBO lighting circuit + a spare 32A RCBO. Selectivity not an issue.
They need a...
Hello everyone. I'm in training but we haven't seen transformers or how they work yet.
I have a transformer here I'm trying to figure out. There are no labels or inscriptions on it.
Primary side has 3 wires: black, blue (AC in), yellow (AC out?) and Sec has red and blue. Labeled USA 18AWG so a...
Hi Everyone,
Hope you’re all well!
I’m wondering if anyone is able to shed some light on a situation I’m having with my neighbour.
I received a text last night saying the below:
“
Hi , hope you’re both well.
My flat came with old key meters for gas and electric. When I first moved in, I...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc