mounted

  1. P

    Chasing conduit to a wall mounted TV and height regs

    I've just recently had the shell of an extension built and will be doing most of the interior except for electrics and gas. I'm planning to chase the walls for where I'll bed in the new conduit to the location of sockets etc before any plastering is done and know the regs on the minimum and...
  2. Dartlec

    Flush mounted enclosure for ring transformer

    Had a quote today at a new build where they've not bothered to put any facility for a doorbell. Customer has purchased a Ring Wireless Pro, which comes with it's own 24VAC DIN rail mounted transformer. Given the location of the CU, it is not the simplest path for a cable run, so looking at...
  3. N

    On-off rocker switch with wall mounted LED controller

    Hi, I'm new to the forum and working on a van conversion - I also dabble in guitar pedals! I have a wall mounted LED controller hooked up to my down-lights. I'd like to be able to turn the circuit on/off at another location in the vehicle (i.e. to make a 2 way circuit). Is it possible to add...
  4. LewisM

    Recommendations for a ceiling mounted PiR Sensor

    Hi, I need to install a ceiling mounted pir sensor however the ones I have previously fitted look cheap and obtrusive, is there any that you guys have fitted that are small and not so crappy looking? Fyi unfortunately I can not fit a recessed one
  5. D

    Is it safe to use 10mm flexi conduit for single circuit cable run, less than 3m, mounted in ceiling, 2 LED domestic lighting points?

    Trying to replace a single run, approx 3M with no bends, of a single 1.5mm twin & earth cable between 2 lighting points in a domestic space. Cable to be mounted IN the ceiling & plastered over. Both points to carry an LED light fitting so minimal current. Is it safe to use 10mm conduit? BS7671...
  6. Dartlec

    Looking for options for low profile surface mounted lights for a solid soffet over garage

    Currently struggling a bit to find suitable lights to fit above a garage door on the soffit. The soffit has a solid joist/beam directly above it so recessed lighting isn't an option, but the customer doesn't want anything too high profile - just wants ambient lighting for the front of the garage...
  7. W

    Earthing woodworking machine question

    Hi, I am replacing a “fizzing” start /stop switch on a metal framed woodworking machine , with an NVR switch with emergency stop. The machine itself is mounted on nylon castors which presumably insulate the machine electrically from ground. My question is therefore, where do I attach the earth...
  8. C

    Light switch with wall mounted remote

    Hi guys This may sound a strange request but the light switch in the garage in our new house is in a stupid position, hidden behind racking and nowhere near the door, so we really struggle to reach to it. At some stage we will move it but we've got loads of other work to do in the house so I'm...
  9. R

    How to shut off 120v baseboard heater?

    I've planned a 20A circuit serving a tiny half-bath in a workshop. The circuit will contain a few LED ceiling lights, a receptacle (not for tools) and a 350 or 400W 120V baseboard heater. So it would not be convenient to shut off the heater via the main panel. When I'm not working during the...
  10. Z

    Surface mounted box.

    Fellow Sparks, My sister has asked me to install a spur socket in her home. I'm going to install a surface mounted box and run the cable via trunking from an existing socket. Is there any sort of surface box which I can install over the existing socket box which has been embedded in the...
  11. J

    din rail mounted bell transformer - earth?

    hi i've bought a hager st303 din rail mounted door bell transformer and a 2 module wylex ESE2 enclosure for it to fit in. i was going to run this off a 3A FCU. i can't see any earth connection on the transformer from the photo - it haasn't arrived yet - and there's nothing to earth in the...
  12. D

    Hager Din Rail Mounted Time Switch

    Has anyone fitted these into an Invicta 3 Type B board? Wholesaler asked Hager whom stated they need to go into a separate enclosure, but couldn't elaborate on why. My preference is to mount them in the DB under the corresponding RCBOs and I cannot see from the spec sheet and photo why this...
  13. J

    Under cupboard lights installation using socket mounted under cabinet

    Hi all. Some advice sought. I have 2 lights under my cabinets they plug into the wall sockets below them. I now want to hardwire the lights as i got a new cooker hood fitted and the spark pulled the power cable out so its now accessible to use. Previously it was hidden. So it looks like a...
  14. J

    CPC Terminal in plastic surface mounted back boxes...

    Hoping someone can help me clarify something. For plastic surface mounted back boxes, why do some have a small metal terminal for connecting the CPC, whereas others don't? Is it just a differemce in quality, or would you generally use the ones with the terminal for sockets, and the ones without...
  15. R

    replacing a ordinery wall mounted electrical socket in france

    I am not a electricion but are competetent in doing these jobs .if I change an ordinary wall mounted socket in my French house ,do I have to get it signed off
  16. P

    Can tubular heaters be mounted vertically?

    As in title, can a tubular heater be mounted vertically? Doesn't sound like a good idea to me, but it would settle an argument if some one could answer.
  17. A2HGO

    Help installing exterior wall mounted up lighting

    We're looking to have some uplights installed across the side of our property, I've purchased a few of these: Garden Trading LABV01 Bovingdon Single Adjustable Outdoor Wall Light - https://www.dusklights.co.uk//garden-trading-bovingdon-single-adjustable-ip44-outdoor-wall-light-p7135/s7145...
  18. W

    Two single gang sockets mounted on the same back box. Is this common practice and why?

    Hi there I'm new to the forum, Just wondering if someone could please take a look at the pic attached (hopefully) and tell me in what circumstances it is best practice to wire two 1-gang sockets side by side like this with a set of T&E going to each. I'm not an electrician but was in the...
  19. gazdkw82

    Wall mounted PIR switch replacement

    Change a 1 gang 1 way light switch for PIR from RS. Customer the idea that it had a lux meter on it and also a manual override just like a regular switch. However upon fitting I can only say it's the most sensitive thing I've ever fitted. Followed the set up and lux levels etc but when screwing...
  20. Gary Tollison

    Fused connection unit mounted on metal backbox

    greetings :) I’m taking a spur from a ring final. A fused connection unit will be controlling the spur. FCU will be mounted on a metal backbox flush in a brick wall. I’m planning on using a junction box to break into the RFC, and taking the spur cable to the FCU. My question is, do both cables...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Daily, weekly or monthly email

Back
Top