Hi everyone,
I am currently installing an additional 4 way CU which is to serve a new extension on the customers house. They have also asked me to alter one of their existing 2 way stairs lighting so that they can have an intermediate switch incorporated (a switch at either end of the upstairs...
hello guys
Client has bought fitting from online, metal cable cap at top with single twin flex dropping down to an e27 pendant with metal casing and no earth.
I'm saying client can't use them what's your thoughts?
Evening all. I have been asked to quote a landlord for a replacement bathroom light as the old ones bayonet fitting was broken, new pull cord as it was one from 1702 which had finally given up and replace the hallway light fitting as it was hanging off the ceiling.
On inspection there are no...
Hi,
just looking for for a bit of advice
i changed a board yesterday for a house I have been working on in their kitchen.
i came to test the bathroom lights in the downstairs room bolted on the back of the house with flat roof to discover that there is no CPC at the light or pull switch, they...
Good morning, :)
I saw lighting circuits done with 2-core cable (red-black) with no earthing conductor. I was wondering in a case of an earth fault is the RCD/RCBO going to trip?
I think if a metal switch or a chandelier becomes live, the RCD/RCBO won't trip due to the missing cpc! But is it...
HI all
Am i being thick here or Ive got to be missing something.
When your faced with lighting with no earth client does not want to rewire as the places is nicely decorated, and they can’t afford the extra cost. How do you fill in your certs.
eg. fit new SELV down lights to bathroom on...
Advice please
installing a in line bathroom fan in a house ,their was no cpc on the lighting circuits ,I told owner I could install fan but couldn't connect to power due to no cpc
advice?
Alrite lads,
I'm a commercial spark so don't do much domestic but a mate of mine asked me to Pop round and change a light fitting in his kitchen 5 min job, he had an old 6ft fluorescent which was shot and he has brought a new class 1 fitting.
I remove the fitting and there's no CPC so I...
This has been posted about a lot but I wanted to ask a really stupid question. I can only run 4mm single g/y to each metal fitting from the board which is dual rcd 30ma. I cannot touch the drops, stipulated by the landlord. Is it acceptable to issue a mwc for this, write a safety letter and...
and here's how it was overcome...................
this was found AFTER rewire when the ceiling was dropped....................no certificates funnily enough!
lister
Thread
available
connection
cpc
earth
lighting
lights
nocpc
Good Evening all,
Been at a property today starting intial tests for a board change tommorow. There are two ring circuits, on one of the ring circuits i had an open circuit on the cpc. Live and neutral where fine 0.4/0.4. I started to locate the break by splitting the legs and joining the live...
Hi all,
A customer wants me to replace a light-fitting and/or light switch for a metallic one, to a lighting circuit with no CPC.
Property must therefore be pre 1966 (ish).
Is this a definite NO-NO.
I would feel very uneasy about doing so.
Ta,
W1ll.
Hi all
Just a quick 1 I'm doing an eicr and basically I've come across 2 pendant fittings with a 2 core flex going to them and no CPC problem is that ceiling has been over boarded with timber panels there's an earth at every other fitting, what code would this warrant.
Been asked to swap over a class 1 fitting for another old existing class 1 on a first floor hallway - however there is no cpc on the light circuit! (early 1960s house). In the loft there is a rfc junction box close at hand. What about putting a 4mm g/y single from the light fitting to the J.B...
I'm looking at the options for customer who has no CPC on lights as is quite common. I know the ESC "good practice guide" - and that all makes good sense.
However most light switches with exposed screws into metal back boxes (where metal box is unearthed because no CPC), would therefore be...
Hi all
Been asked to quote for a board change. Had a quick look round the place and discovered lighting circuit has no earth. Where do I stand on this?
Current board is 3036s and will be replacing with rcbos as wiring is quite old. Will also be bonding the gas and water from 4mm to 10mm.
Paul117
Thread
board
change
circuit
cpc
electrical
guides
lighting
nocpc
practice
sticker
Went to change a light for a local estate agent today, No cpcs to the lighting circuit would i right right if i said the circuits would have to be rewired?
Been asked to change a consumer unit
On inspection found out that customer had done much of the work himself - approx 20 years ago
Currently has old Wylex NN Board
Ring Mains & Kitchen appear OK - T&E
Lights have no cpc, except for a couple with metal fittings.
The lights with metal...
SB-LEC
Thread
borrowed
change
consumer
consumer unit
cpc
earth
lighting
lights
nocpc
unit
When doing a CU change and lights have no cpc. Every room has class 2 dimmers and lights. ceilings are like 20 foot tall. How would you guys go about Insulation testing? L&n to cpc ain't an option and removing all lights and bypassing dimmers is consequently going to take some time... What would...
Hi all just done pre site survey on a job found the following (never come across this before)
2 ccu's in the property 1 located next to the incoming head (A) and the other (B) is located approx 15 meters away
Both CCu's are feed via henley block. (A) tails are 25mm however the cable feeding...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc