Is it ok to control an outdoor double socket with a programmable switched timer - the type usually used for lighting? The sockets are for a pond pump and filter which use c 35w while the timer switch wd be mounted in a shed and on a 6a mcb. My sparky didn’t sound concerned - he basically said...
I have outdoor lights that are controlled by dusk sensor and then timer (for OFF) on the right of the picture. The switch to the left of the box powers off the entire fusbox therefore I cannot change that as I have other things I keep on). What do I need to buy (switch/plug?) to swap the old...
I have an arena lit by 100w LED floodlights, to get through planning my dad fabricated hinged collapsible poles and each is wired to a plug to make them 'temporary'
I've had so many replaced because IP65 does FA in rain. always replaced by electrician and rewired at the light.
Now I'm...
Checkout the latest case study from RF Solutions:
The SWITCHLINK is an RF wireless switching system ideal for outdoor lighting remote control. The system uses a battery-powered wall gang switch and a 230Vac MAINS receiver and has a range of up to 200 metres. The MAINSSWITCH, a similar system...
I've been thinking of adding a couple of outdoor weatherproof sockets to the same wiring I used to connect my CCTV camera, this was previously just powering two outdoor lights which I have removed. The fuse is only 6Amp on that ring so I wouldn't be plugging anything too power intensive into it...
Hi all,
I am installing a custom sized (15ft X 17Ft) Aluminium pergola in my backyard on a concrete with tiles.
The Aluminium pergola and kitchen are powered from one of the outlet from the house.
Please note, the pergola has inbuilt lights and will be powered from one of the outlet from the...
Just received a Eufy CCTV floodlight camera (This one) which requires existing wiring. We have two outdoor lights on the side of our house with a cable running between them, my plan is to T off of this cable using a weatherproof junction box and cable glands.
My question is what type of cable...
Grateful for a kick in the right direction on the following: a telecomms engineer stated out that an outdoor metal cabinet (earthed & bonded) was an unsuitable enclosure for a network switch and patch panel to be installed into, as it was not IP rated.
As it happened, the size of the cabinet...
I would like to add a flood light camera and outdoor outlet to the front of my house where there is no existing wiring. I plan to get power from an outlet inside my garage and feed UF cable through a hole that I will drill above my garage door. The roof (eave) extends passed my garage door and...
This is the setup I am trying to put together. No idea what to buy in terms of parts. The bulbs will be low watt patio style incandescents.
I am in the UK and these will be for outside. Just want to make sure I don't electrocute myself.
The lights will be hanging - not levitating like in the...
details
12v outdoor fairy lights
20m in length,
coaxial socket
UK 240v plug that with built in 12v 1amp transformer
220v-plug/12v-transformer has cable out with coaxial plug connects with coaxial socket on 20m fairy lights
Problem is I want to plug this in far away from the house say...
Hi all,
I have a Malibu 120W Light timer for low voltage outdoor lights. When I manually set to ON, the lights go on, so I know the lights are wired correctly. But the timer is set to run off the photocell: lights on at dusk, and off 4 hours after dark. However the lights do not turn on at...
Hi Guys,
Wondering if someone can advise me if i can do the following. I just want the wiring to be neat and tidy and not have so many outside, also happy to hear your recommendations of course!
RCD FCU to Outdoor Double Socket using 2.5mm >
From Outdoor Socket to another FCU with 3amp fuse...
I have installed and outdoor enclosure to primarily house outdoor network and IoT devices. I need power for PoE injectors, power supplies, etc. The Carlon outdoor enclosure is 12 x 12 x 6 and has a sealed lid attached with screws. I extended the existing outlet (GFCI) by using 1/2 PVC...
The previous owners of our property had non in ground rated electrical hardwired into the basement from an outdoor submerged pond fountain. Needless to say it was causing issues. I disconnected and dug up the corroded wiring which went into a switch plate on the outside wall. Layed down new...
Good afternoon.
I’ve recently moved into my new home. I’ve taken down a conservatory and bagged up the existing indoor socket that is now exposed to the elements.
I’ve bought an outdoor socket and I’m looking to simply replace the existing one, using the existing wires. There isn’t a recess...
I have a dark dingy old Victorian coal storage area in the basement, just below street level, accessed via a gate and stairs to the basement flat. The sheds used to store coal but then became a bin storage area but the council won’t collect bins from down there anymore, so it’s just been lying...
I am planning on running wire about 135 ft (100ft underground) from a panel (20amp breaker) in our garage to my outdoor bar. The bar will house some LED string lights, a tv and a frig at this time. Heat and Grilling are propane. I was planning using 8/2 NM in a conduit to a 2 breaker (20 amps...
Hi!
I’d like to install a pedestal-mounted (230 V, 30 A max - programmable) EV charger close to my driveway, which ends about 12 feet away from the house, on the other side of a landscaped rock wall of sorts. While I am at it, I would like to oversize the circuit to allow a second EV charger to...
Hello, I am looking for some recommendations for external motor isolators with Aux contact block. Ideally large enough to gland 3 cables at the bottom, most likely 3x M20. possibly 2x M25 1x M20 for a few. I have taken over maintenance on a site and most isolators are unserviceable and will need...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc