Am I correct in saying that a light switch (or even a socket for that matter) can now be installed inside the bathroom as long as the circuit is protected by an RCD and also it is outside Zone 1?
Thanks for feedback
Hi,
I'm in need of some help. What is the best way of acheiving a HDMI connection from a remote HD source to the flat screen on the wall? All cables concealed and its all flat plate..
Bought a couple of these HDMI outlets, but can't honestly see that it'll work, even with a 47mm box.
I'v seen...
Sure this question has been asked many times. Point me to previous post if need be. What coding do you use on pre 17th edition socket outlets that would now be installed with rcd protection. However currently not protected.
Also code 2 for any bonding on cable tray and ligh diffusers this is...
Hi
Just got off the phone with a very confused customer. Who is looking to have 8 sockets added to there living room. Board is old style wylex.
I said that they may need to have a rcd installed to which I got the last electrician was just going to put it down as a advisory on a mwc.
Now I have...
Hi all, Considering mounting my T.V on the wall in my bedroom and as I'm decorating I thought I might as well put a few more sockets in instead of having extension leads on the floor and wires hanging down the wall.
My question is this. I opened up the socket that is there and what I thought...
Most new kitchens you seem to have no option but to install sockets (for wash machine/dish washer etc) under the sink in the base unit.
I do not believe there is any reg's restricting this but some kitchen fitters i come across still seem to think it is taboo (though they do it anyway).
Am i...
Lioned
Thread
aus
discrimination
outlets
problem
socket
sockets
under
Hi all,
I've been looking to get hold of a 4g outdoor socket box with an appropriate IP rating (54 - 66) & 30mA RCD - I only seem to be able to find 2g options or weatherproof boxes that hold an extension lead, which I 'd prefer not to use.
The requirements from the client are to supply 2...
Tasty
Thread
aus
extension
outdoor
outdoor socket
outlets
route
socket
sockets
thoughts
Can someone please clear this up for me:
Are unswitched socket outlets (power) still allowed to be used under the Regs. If yes, where and why? Is it ok when there's a fused spur attached...? I don't know.
Being told in college that they're not used anymore, but then I'm helping to fit them...
what code would i give on PIR for skt oulets in commerical property with no rcd protection?
all skts Zs are under max values and only intended for staff:confused:
hey anybody know why top part of my outlet dont have power but bottom
half works fine. also there is no switch that controls or has any effect to this outlet maybe just not wired , any help
Thanks
hi all
just wondering what you all would put for a pir when the domestic install has a number of unswitched sockets.
these are not controlled by a spur or 20dp switch.
is unplugging enough to be classed as isolation.
ta
vitoboy
HI, I've been asked to do a pir on a domestic installation, Means of earthing is a TT system using a 100 mA (not s-type) rcd as the main switch, covering all circuits. House is a rental property...Is there any real problem with this with regard to regs? would appreciate any advice thanks.
More questions....yawn.
I am required to wire a couble of flu's into a small extention within a building.
I have removed the lights which were at high level before the extention was built.
These lights were connected to a 'click' outlet.
I was hoping to re-use this 'click' outlet to...
Hi everybody,
I've been asked at college- when installing additional lights to a house, whether it is necessary to install a seperate circuit when the existing lighting circuit already contains 10 lighting outlets. I know as a rule of thumb it's 10 lighting outlets per circuit, but what...
bathcity
Thread
already
calculation
circuit
help
lighting
lighting circuit
outlets
Hi all
After some advice on measuring Zs at socket outlets using the megger 1553 what setting should the megger be on for this test ? i no i have to use the plug in plug i got with my megger just not sure what setting the megger has to be on ?
I no how to calculate Zs by calculation using Zs...
Hi all this is first time I've posted so appologies if I've missed anything out.
Recently just done a i&t and the ring main in one part of the commercial building is completely "ballsed up" to say the least. Spurs off spurs with rings of them and even more spurs off them. Going to have to...
Commercial greenhouse - panel has a 4 pole 40A 300mA rcd feeding 3 x 3phase 16A socket outlets with 25A 30mA rcd's built in. Under 17th edition is this 300mA illegal. Customer wants local RCD's for ease of nuisance trips.
Hi all,
I understand that socket outlets that are to be used for powering appliances in a kitchen must have an means of isolation accessable at all times.
I was wondering what people think of using a wireless reciever socket outlet like this one from homeeasy:
Home Easy Receivers Remote...
trueblue188
Thread
isolation
kitchen
outlets
socket
switch
switches
using
wireless
Hi, I'm about to swap out a domestic Consumer Unit in a building with Socket outlets mounted all over the skirting boards. Other than the socket outlets in the kitchen - do i have to move all the socket outlets up to 450mm and what about the issue of the socket outlets being mounted on a wooden...
Hi all,
Ive just bought a box of 50 double skt outlets to BS1363, manafactured by GET England, but they have only one terminal for the CPC.
The on-site guide (page 67) states "socket outlets must have two terminals for protective conductors. One terminal to be used for each protective...
sivoodoo
Thread
cpc
double
having
outlets
protective
socket
terminal
terminals
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc