parts | Page 2

parts

Recent contents View information Top users
  1. N

    Manage to create simple lock from car parts

    Hi looking for advice about electrical connections with car locks, below are photos of lock and device locking may someone tell me what I doing wrong because it not work . Basic car lock brown and grey cable when I switch it positive and negative cables from battery it close when I swap them...
  2. J

    Washing machine parts nr need for AWG 5122

    Hi Im looking for bearing partss number for Whirpool AWG 5122
  3. cliffed

    Extraneous parts

    Code..for extraneous conductive parts not bonded at entry to various points @ school,the main water & gas are bonded @ intake,but water & gas are entering either underground or overhead elsewhere,& no definite earth connection.
  4. L

    LED Lights - electric fire - where to get parts

    Hi all. I am trying to repair a wall mounted electric fire ( glass fronted type with pebbles along the bottom ) Fire itself is working, ie heating Ok and the fan works. Problem is the lights which give the flicker effect have stopped working properly, there are three lights which are on...
  5. D

    Parts for vintage service station lights..

    I have some vintage service station lights similar to the attached photo. However, they don't have any sockets, nor anyway to connect them to the conduit. I've been unable to locate these parts.
  6. J

    Electric Car Charging

    Hi i need some info on a few electrick parts for a electric car any help would be so greatfull 1573401889 I have a Peugeot Expert fully electric 3 phase input But the inverted are fluxuant from 200v /400v Then a converter that's 288v input and output of 12v 50a I'm lost help lol
  7. A

    Dimplex duo heat 300n storage heater Spare Parts

    Hello, Been remodelling my sitting room and have moved my dimplex duo heat 300n storage heater. This has not been switched on since the end of last winter. So last night,when switched on for the first, it did not come on. Tested power from E7 and it is fine. The comfort heat panel works off a...
  8. J

    Which course to refresh for 16th Edition City and Guilds 236 parts i and ii

    I originally passed my City and Guilds 236 Electrical Installations parts i and ii courses, along with working 4 years for an NICEIC registered company back in 1994. In 2000 I started to work in the Fire and Security Industry, and since 2013 I have been in Rail and Telecoms, as a design /systems...
  9. gunsmokejp

    Electric Scooter Parts. 350W motor 36v Battery

    Hello i have for sale the parts of this scooter. Everything is working fine is just the holding mechanism is a bit wiggly(missing a screw) and the speed indicator is not working. The cable from the battery to controller has been worn out so i think this might be the issue. The scooter is one...
  10. Thomas Simons

    RCD Protection for lighting within communal parts

    I'm due to start working in a building which houses lots of flats over 6 floors with 2 internal communal stairs. I'm due to replace 13 ceiling lights per floor/stairs from a halogen bulkhead to a ELD 17w LED microwave/emergency bulkhead. Each floor is fed from a Square D B6 QOE MCB on a 3...
  11. P

    How long warranty to you give on parts?

    I recently quoted a customer for a few bits and pieces including supplying and fitting an external pir floodlight. She emailed me to ask how many 'years' warranty I give on the floodlight, and I said a one year parts and labour warranty. She emailed back to say that usually they come with a 2...
  12. J

    Bonding Extraneous Conductive Parts

    hi. Question re bonding a metal where cold comes in as metal pipe ground into house. So cold will be bonded where service comes in. Read article in wiring matters 2019 about changes for part 18. Example given of faulty kettle where fault to earth exists at kettle, some one touches kettle...
  13. N

    Extraneous Parts Earth sizing

    Customer wants to take power from an existing garage (with board) to supply a greenhouse, to be fitted with ip rated switchgear. The greenhouse is made of aluminium. Since this is an extraneous conductive part am i right in thinking that the aluminium frame would require a 10mm bond at least...
  14. S

    Extraneous conductive parts

    Morning, so just finishing off the install to a shepard hut which is located in a field. The construction is steel chassis, plyboard floor, timber stud clad with corrugated sheets. The corrugated iron sheets which clad the unit are plastic coated and there is no continuity between each sheet...
  15. S

    Help needed re simulator parts power requirements

    Evening all, I have built a 2 DOF VR Roller Coaster simulator. I am now adding additional realism, specifically wind. This is the specification of the inline air pump that I am going to use, Inline Blower | 270 CFM 4″ In-Line Bilge Blower Fan -...
  16. Ian1981

    Extraneous conductive parts

    Hi all. Looking for opinions on here. I’ve identified during an eicr that a dry rise pipe used for firefighters in the building is in fact an extraneous conductive part and that it is not bonded back to the MET. However what I’m questioning is it’s accessability to be touched in the event of a...
  17. B

    THE ANNOYING PARTS OF RUNNING YOUR ELECTRICAL BUSINESS

    Hey all, I'm a qualified electrician and have been for 20 years now (Although not on tools right now). I'm in the process of putting together a course that guides/helps/coaches and provides systems for people to conquer their pain points. I've experienced the long days, then getting home and...
  18. gazdkw82

    Tv - 75v exposed conductive parts

    mother inlaw says - I keep getting a shock of the back of the tv when I try and move it to turn the plug off. It’s a wall mounted tv in the kitchen. I thought initially it must be just static but told her I’d have a look. As it happens, every screw, or exposed conductive part on the tv is...
  19. KWJ41

    JIB Electrotechnical Certification Scheme (ECS) Qualified C&G 236 Parts 1&2 in 2003, updated to 17th from 16 Edition in 2009 - But not JIB eligible

    Hi - I'm new to the forum and in desperate need of advice. I'm a fully qualified electrician qualified under C&G 236 in 2003 (parts 1&2), I updated to 17th from 16th edition in 2009 and hold an up to date safety passport through the ECS. I've recently gone on my own after being employed for 14...
  20. HumbleWorker 91RT

    Worst and Best parts of your day to day?

    Alright guys and girls, Just wondering seen as there are a lot of different types of electrical workers on here wanted to know which parts of the job day to day wise you enjoy and which parts could you really do without? Hopefully get some decent ideas from those doing the designs to those...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top