plate

  1. Lucien Nunes

    Brass gland plate for SWA

    Has anyone used a brass gland plate to earth a line of SWA glands e.g. at a DB, and had anyone such as an NICEIC inspection flag it up as non-compliant? I am proposing to screw a flat plate of brass onto the top of the DB and mount the glands through it with their usual locknuts, A brass bolt...
  2. T

    Cooker hood and bathroom fan connection via duel appliance outlet plate.

    I wish to install a bathroom extractot and cooker hood from an existing 32 amp 6mm cable . I intend to use a duel applliance outlet plate to split into two 6mm cables running to seperate 3amp FCU's from there 1mm cables to all parts that follow . See diagram . Is this in line withs regs. Thanks .
  3. C

    does anyone know the location of the heater resistor on a 12 plate vivaro?

    Looking to change it but don’t know the location
  4. I

    DUAL APPLIANCE OUTLET PLATE

    Hi everyone, I have read few posts about dual appliance outlet and wonder now if it can be used in my case. I have 32a 6mm cable to 45a switch supplying 6200w hob. Current oven is 2,4kw 13a plug. It will be replaced with 7,4kw induction hob and 3,6kw oven. Can hob circuit be used for both...
  5. F

    6 Inch Solid Stove Plate Wiring

    I have a Salton Mini Oven with one 8 inch and one 6 inch solid plates. The 6 inch plate has stopped working and I went and got a new plate from ARB today but when I got home, I realized the new plate has 4 connecters numbered 1, 2, 4, 3 where the old one only had 2 (Live and Neutral). I assume...
  6. D

    Oven with 13a plug top

    Been asked to fit new oven , which comes with a 13a plugtop , there is no socket close to plug into , if i cut plug off and connect into cooker unit connection behind cooker , do i have to adjust the 30a cooker unit fuse.
    • daveboy
    • Thread
    • asked comes connection cooker fit new oven plate plug small sockets unit
    • Replies: 18
    • Forum: UK Electrical Forum
  7. S

    Motor rating plate help 3phase

    Evening all, got this rating plate on a portable feed augar motor, it's currently wired in some seriously past it SY cable, the farmer wants to renew it , I've suggested H07RNF as best choice, but I'm not clued up on reading motor plates to size it, I see 29 on the plate, and assume it to be...
  8. K

    Change bt master phone socket for metal face plate

    Hi all, Trying to change a facetted. Not sure how to do it. Got a bit master phone line with this layout A White B Orange 2 White 3 Green 4 Black 5 Orange I want to change it for a new metal face plate, which has 1 2 3 4 5 6 What do the cables do. Thanks for your help Cheers Tony
  9. MikeMaMan

    blank plate within 300mm from the cooker?

    hi. i know what sockets most be at least 300mm from the cooker. but if socket is removed and blank plate installed, does it still need to be 300 mm away form the cooker?
  10. N

    Attaching a round sconce plate to a 1 gang junction box

    I have a 1-gange box on the wall where an old wall sconce was. The new sconce has a round wall plate. Is there a way I can convert the box to accommodate the round plate without having to replace it with a round junction box?
  11. B

    Seimec 3 phase motor plate shows wiring for 240v? Can I have 1 phase out of it?

  12. KeenPensioner

    Quinetic switch on 2 plate system

    I understand how to fit a receiver and quinetic switch in a 3 plate system at the ceiling rose. Is there a way to do the same when the feed is taken to the switch (not enough room for receiver etc)?
  13. D

    Is a cooker outlet plate a requirement?

    Quick query, When installing a kitchen, is a cooker outlet plate a requirement (recommendation) or could I bring the heat resistant flex from the oven directly into the cooker control unit (45A switch with socket outlet)? D
  14. K

    Connection above or below terminal screw plate

    Does a wire attaching to a screw terminal on a standard receptacle outlet go over or under the little brass movable plate, please? Thanks
    • Kitkat
    • Thread
    • below brass connection little outlet plate please screw screwfix standard terminal under wire
    • Replies: 4
    • Forum: UK Electrical Forum
  15. M

    Metal face plate ok with plastic pattress box

    I’ve just had a new stud wall put up. I have chrome light switches throughout the house but with metal pattress boxes. Am I correct in thinking a plastic drywall pattress box will be ok with a metal switch as long as the CPC is wired into the faceplate....or do I put in another noggin and use...
  16. Lee Gold

    3 plate method, loft light only turns on if bedroom light is switched off?

    I wired 3 plate method loft light from supplying from my sisters bedroom light ceiling rose, the only way the loft light I fitted tuned on is if my sisters bedroom light was off, so then I it was really bugging me I went back to my connections supplying the loft light at my sisters ceiling rose...
  17. multimick

    flex connection plate zone 2

    is this allowed or am i being pedantic ,it aint ip x4 , it's feeding a panel heater that is ip 24. so that's ok at least
  18. L

    UK Need for an outlet plate and a 13 amp socket for new oven/gas hob.

    Hi.I am a DIY enthusiasts and do have the basic knowledge of electric science. As I am about to refurbish my kitchen,I have bought an electric single oven power rated at 3.60 kw and a gas hob power rated 1.3kw. The existing setup is:6mm t/e cable running from CU/Fuse box (on a 32amp MCB) to 45 A...
  19. S

    Mitsubishi colt

    Hi, my daughter has a mitsubishi colt 1.1 litre 56 plate. Her car beeps 3 times and then changes the radio station. This has baffled me. Does anybody have any ideas please. Thank you.
  20. Moley

    Anyone else got a '19 plate (dead!) Transit custom??

    It seems that all Transit Custom 2.0 vans built between Feb and Sept 2019 were built with injectors that can die at any time. There was a coating used on the inside of the injectors that can come loose and block up. All four injectors and pipework have to be replaced. My Transit with 4200 miles...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.
UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
Back
Top