Hi All,
We have an old Country villa in Spain. The housing electrics were not good so the house recently has been completely re-wired to a good standard.
Due to some miscommunication with the electrician however, he forgot to create a separate circuit for the electric cooker.
Looking at the...
Hi,
My current oven is hardwired to a fused connection plate with a 13Amp fuse inside and power switch. That is then connected to the MCB labelled kitchen. The MCB switch labelled cooker is actually connected to the hob. Could I cut the hardwired cable and connect an unfused plug socket, which...
have a set of lights that i would like to use plug over battery.
have a few plugs and old sets with cables could Frankenstein together if doable.
this is the set if anyone has any suggestions on how/what min transformer plug would be required.
its a 20m set and i have another 20m set so...
we just replaced our hot water tank with hot water on demand (natural gas) and still have the old power run for the tank which is 30a 240v. I would like to use that power run to put a plug in for my RV ( 30a 120v). currently the run has a ground and 2 hot wires so I wanted to know that if I...
What is best practice when unable to access a plug on a class 1 appliance. Specifically a washing machine in this instance. There is also no isolation point where it is wired into so the plug is definitely behind f the machine but completely unreachable
Hi,
I have a Prima Tumble Dryer which I have had for 5 years.
Just recently, the plug and socket melted. I replaced both and it melted again. I replaced again and again it's getting hot. I measured the temp with a laser thermometer which said it was 42.5oc. I drilled a couple of holes in the...
Hi all, we had our gas hob removed months ago and finally just got round to putting an induction hob in.
Its a normal 4 ring induction but one of these newer 13amp ones with a moulded plug on.
In the kitchen we have a 45amp cooker switch on the wall which feeds a 2 gang socket in the cupboard...
Hi all,
Just recently moved into a renovated house in the UK where a desk is quite high, so the plug socket above it has had to be put in upside down! Other than a bad case of OCD, is this normal/ok?
Please see attached photo.
Cheers,
Will
Hi all,
Figured I'd come straight to the experts with this one because I don't have a great deal of electrical experience.
I'm a designer at a furniture manufacturing company. We manufacture furniture almost entirely out of folded sheet steel profiles.
Currently I am working on designing a...
Hi,
I'm trying to rewire an old plug. I've rewired a few in my time, but all have been with the post-2006 wire colours. I have this old welder, not really sure how old it is (I got it from a friend who got it from the dad of one of the guys he works with) but safe to say it is definitely...
I received multiple quotes to install a long run for my electrical outlet NEMA 14-50 for my tesla. The cost is huge $1800 give and take.
Basically it will be in the drive way running from the electric panel in the middle of the house to under the floor to the crawlspace (20ft), then under the...
Hi all , I know that you are allowed to do like for like in your own home Ie change a wall light etc.
I have an issue with one double plug thats on a ring main. The wires are very short and after tiler tiled the wall I can not get plug back on as the wires are now too short.
Ive been told to...
Hi all,
Just looking at starting some testing since newly qualified, don't know if this is a stupid question or not. Is there an allowed tolerance for movement on the pins of a plug?
Obviously if they move a lot that's no good but what if they move a little when you wiggle them? Just curious...
My house had previously been wired for a generator (probably not by code to this day) but previous homeowner disconnected and instead hooked up car charger to that circuit. I would like to place it back to a generator hook up plug for emergency power. I have included labeled pictures of outside...
Hi Guys
Got Client asking me to fit these floors sockets…. Got my doubts, looks like cheap piece of tat !!
Just sent me photo from what they’ve seen on Amazon.
Which county you reckon this is for ?
Cheers Sy
Hello,
I have acquired two FOGLIO wall lamps that I want to convert from wall lights into lamps. I'm not familiar with wall lighting so first I wanted to know if this is possible and if there are any risks I should be aware of. Secondly, if it is possible, what would be the best way to go about...
I had to replace a surface plug socket box after the plasterer destroyed the old stuff.
It has black, red and earth wire, 3 of each and look quite thick (the earth wire looks like it should be used for barb wire abd isn't covered)
Sticking all of that into a new faceplate isn't working so well...
I have a small power washer with a two-wire cord and GFCI plug. My outdoor and garage receptacles are on a "house GFCI" circuit, wired in series to one GFCI receptacle. I tried to use the power washer and the plug GFCI would instantly trip when plugged-in and instantly re-trip when reset. I have...
Have a single plug socket which has been working fine for years. It is behind a unit so nothing has hit it. I looked at the socket and can seen no discolouration or anything on the outside to indicate a problem. Took the socket out of the wall and again nothing to indicate a problem and all the...
Hi, I have purchased a piece of equipment from China and we are required to finish the final wiring. They have supplied a length of 3 core 6m cable, which seems excessive.
The unit has a power consumption of 1kw - 2.5kw
Rated voltage - 220v
Rated power - 3.42kw
Rated current 20a
Would it be...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc