Hi all, i hope this is in the right section (if not i do apologise and will not do it again).
I need some help with a very problem customer, I have carried out a c/u change and issued a EIC, then 2 weeks later I get a phone call blaming me for the boiler not working, called to the address and...
Have a job wiring single storey extension. Lights, sockets extractor fans etc and all ok and on with job.
Customer now decided to put in underfloor heating and plumber on with that now.
Never wired this type with zone valves and thermostats etc to three rooms.
Anyone know where I can brush up on...
Just got a call from my sister who had a new bathroom (and 10.5kW shower) fitted 4 weeks ago because their cartridge fuse has just blown. She proceeds with the "i've popped down B&Q" to get a replacement fuse, all very well and good, until she tells me its a 30A fuse!!!
Suggested she got hold...
Hi all
I have just spoken to a friend.
She is having a Power Shower installed.
The plumber has already started the job - he has done the pipe work etc.
Apparantly he has let my friend only just know that he wont be able to sign off the electrical side of the works as he does not hold the...
chrisgc
Thread
advice
covered
electrician
electricians' talk
friend
installed
issue
needed
plumber
power
power shower
shower
I was asked to connect up a cooker last week, went round, no water or gas bonding, 6mm main earth, no supp bonding, no RCD in sight. Agreed with the customer to install+upgrade earthing and wire a new circuit for their 10.7kW appliance (as they thought I could just wire it into an adjacent...
Well looking for help again.Got asked to have a look at an immersion heater that trips the rcd as soon as it reaches set temp.This can be set at 50 degrees to 90 but as soon as it gets to the temp off goes the rcd.Have cheaked ir on cables back to board no problems,restance of dual elements 1...
pfa
Thread
aus
electricians' talk
element
heater
immersion
immersion heater
plumber
problem
rcd
tripping
tripping rcd
Before everyone starts thinking its me thats done this, it isnt the case!
I have recently wired an extension, all is fine. The plumbers came to install the Air source heating system (Pump and Boiler) The client had told me what his requirements were, they did not include wiring the heating...
Alright fellas,
Went out to wire in a boiler today and the plumber has cut the water main bonding:eek: to make "a bit of room"
nice
Can I make a joint and still comply? or do I have to run an unbroken cable?
I was thinking possibly a crimp?
any ideas?
Benny_Boy
Thread
bonding
electricians' talk
main
main bonding
plumber
Hi.After years of plumbing,(fully qualified and GSR)I've advised my son to train as a spark.Best route into trade?Cost?We are in the North West and obviously I'll be funding this.He is 19 BTW.Cheers
I have a querie, i have recently started my own business after working for someone for 15 years, passed my niceic domestic installer assesment and am getting very busy.
Now to my problem, what do we do if we go to a customers house as their shower is bust. NO RCD PROTECTION, NO MAIN BONDING TO...
Hi everyone - I was on here ages ago asking a few questions and got some great advice - I now need your help again.
I previously wanted to re-train and start up as a Self Employed Sparks but was wary about going in the deep end, I am instead re-starting my old Plumbing business and will soon...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc