probe | Page 3

probe

Recent contents View information Top users
  1. trypod

    Megger MFT1730

    Got one at last! First views: Good points inside of carrying case better Probe ends better Easy to use, better display Quick start guide better than the MFT1530 guide Rechargeable batteries Bad points No indepth guide price http://img717.imageshack.us/img717/1340/1730v.jpg...
  2. V

    External earth fault loop impedance Ze

    Hi all Just checking this procedure is correct for Ze This is a live test so with the consumer unti front off i would lock off main switch keep RCDs on and all MCBs on. Dissconnect the main earth. Now on the megger 1553 i would set it to no trip and use the 3 lead method ? So green...
  3. D Skelton

    Switch probe?

    Hi guys, what is the SPL1000 switch probe for that is included with the Megger 1553? What does it do and how do you use it?
  4. E

    Fluke 1651B

    Fluke 1651B, 5 months old with calibration. In excellent condition with no marks or scratches. Still has protective cover on screen. Selling for a friend who bought it for a 2391 course but never did it. Only used a few times (most recently by me to confirm it reads the same as my meter, which...
  5. B

    Testing with 3 probe instrument help needed

    Hi, I am fairly new to all this so please bare with me. I have been up till now using a 2 probe megger. I have now purchased a 3 probe Kewtech KT62. Can anyone please inform me what test use 3 leads and when I join the 3 to become 2 etc. It does not say in the Kewtech manual! (specifically...
  6. IQ Electrical

    Anyone using a Megger 1553 Bluetooth?

    Does anyone use the Bluetooth setup on the Megger 1553? We had use of one for a week and found it very clumsy and a nightmare for Periodic Inspections where you might not wish follow the usual testing sequence. Just wondered if the latest versions were any better?
  7. F

    Metrel Easitest RCD-auto

    Hi all, I am encountering a few problems using my Metrel Easitest to check out RCD protected spurs; when I use the meter on 'auto-RCD' it comes up with '0-V' or 'PE' with flashing warning triangle and the full 6-step auto test is not carried out. The leads should be OK as other tests are done...
  8. S

    Help with testing phase rotation

    Hi guys looking for help with testing three phase for correct rotation. I have a 2 probe voltage tester with left or right rotation indicator. Probes are marked L1 and L2. Would I be right in thinking that to test rotation I would need to test as follows. Probe L1 to phase 1 probe L2 to phase...
  9. W

    kewtech probe tips

    does anyone know there i can get replacement probe tips for kt64,thanks
  10. K

    under floor heating stats

    Hi lads, anyone know if a Clock Thermostat OCD2 by OJ electronics can be replaced with a 'warm up' type controller? Does anyone know where I might source the OCD2 from, struggling online to find aywhere. any help appreciated
  11. T

    Replacing underfloor heating probe

    Has anyone ever had to replace an underfloor heating temperature probe? I know there supposed to last but if one ever did fail I can't see how it can be replaced, it comes with a length of flexible conduit, easy enough to pull the old one out, but would be a nightmare slide a new one in...
  12. D

    Where to buy test probes for Fluke 1651?

    I've lost the green probe end to one of my leads of my Fluke multi tester 1651. I've found sites that offer the whole set of leads for £60 but just want the replace the probe end! Any ideas? Being green isn't such an issue (a little electrical tape could denote its purpose). Thanks
  13. W

    Replacement Probe Guards?

    Hi Where can I get replacement guards for my probe tips for my fluke t120 voltage indicator? Thanks
  14. W

    Underfloor Heating Question

    Hi All Got to install some underfloor heating in the kitchen and new conversion, i have installed these before but on a much smaller scale. Question is i have two heating mats at 10m2 each both together come to just over 15amps, is it ok to put these on a 16amp or do you think it mat be a bit...
  15. E

    Megger MFT 1552 what is the red probe used for?

    Megger MFT 1552 what is the red probe used for?
  16. Z

    Testing Earth Electrode with low Ohm Meter

    Using a low ohm meter (or multimeter)Is it possible to place 1 probe on the incomming earth at the CU and the other probe on (disconnected) earth rod to get the resistance of the rod (minus the external earth path which forms part of the Ze, wander leads etc). I know its not the correct...
  17. E

    Underfloor Heating

    Hi a friend has had a sparky in to do the first fix for his kitchen and conservatory. However after numerous phone calls the guy will not come back to finish off the work. I went around today to see if I can help and am a little bit puzzled. There is going to be 2 underfloor heating systems...
  18. T

    Megger 1502/2 or 1552 ??

    Could anyone tell me what the difference is between these 2 testers ? Which is the better one? if any difference
  19. B

    bath rm under floor elec heating

    hi all does any one have a great experiance in electric under floor heating need a mate in a bath rm but obviasly the stat is not is not ip rated all services are to be rcd. protected looking through some litriture and there is a floor prob will this be able to be selected to control floor...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top