problem

I have a grundfos sololift 2 wc1 macerator that isn't working. It's about 3 years old. When the toilet flushes the bowl just fills up but the motor does not kick in. There is power going to the unit, The macerator motor/pump turns freely. I took the motor apart in the hope that there may be...

I have a 4kw system and a Solic 200 installed - all good since installation. I had a Solis inverter and Pylontech battery installed, but the Solic and Inverter do not work together! The Solic boost button does not work and I have the warning lights. I had hoped and asked the installer that if...

Hi, I have got this DC to AC power inverter that draws excessive amount of power when I start up a motor. The motor is a 1300W one and my other inverter draws 1800W on start up, the one with a problem takes 3200W. It's a low frequency inverter with simple power board and a large coil. I have...

Last couple of days, the forum runs slow. It can be fine when first opened, then after a couple of minutes freezes, or I get an error message. This is using forum on iPhone 11, haven’t tried laptop yet. Closing Safari down, then reopening seems to help… but a few minutes later, it happens...

Hi all, I am hoping someone can help me with my problem. Just started renting a place and it has under cabinet LED lighting in the kitchen. It's connected to a wall switch but it takes anywhere from 2 to 50 flicks of the switch before the lights come one. I have tried slow on/off patterns, long...

Hello all, Ran into a curious issue last night with my basement light circuit - here are the details of the circuit (diagram also attached): 15a AFCI\GFCI combo breaker in panel 3 Switches (2x 3-Way Switches and 1x 4-Way Switch in the middle where the power comes in) Load - series of light...

I want to add indicator lamp for ON,STOP, and trip , which terminal should i connect? And what about terminal no 1 and 2? Please help

So, This is the Main disconnect for a Panel that provides Heat to units. I shut off the Main. Worked on the panel. Went back to energize the Main Disconnect and this is What happened.

I recently had a solar installation at my home. Immediately afterward, a GFCI outlet in my garage stopped working, had no power, and could not be reset. At the same time, my two outdoor outlets stopped working. I first checked the new breaker box the solar installers put. However, no breaker was...

Hello everyone I hope you all well,, I have a question regarding old method install rosy lights-switch and connect in the box,I have a problem with one fault sort it ,the light doesn’t work,I needed help,I have experi connect in the switch…

I have 4 1w LED marker lights AU-WU682/1R in the ceiling with a AU-LEDD16CC driver in the loft. In the same bathroom I have 3 of the same marker lights in the floor with a AU-LEDD16CC driver in the room below. The dimmer switch I have is SF2184BC 5-150w. Each set of marker lights are currently...

Hey guys, hoping someone can help with my problem.! A client of mine asked me to rig-up a little solar system to power a diaphragm air pump (230V/3A) for a cesspit. Solar/low voltage isn't something that I'm that familiar with (I'm a sparks), would have much rather just laid some new armoured...

Re: Danfoss FP715Si Programmer Anyone have any direct experience with this unit? NB: There are quite a lot of posts online about this issue, but nothing I have found that has found the cause. This Danfoss FP715Si Programmer that works fine. But the following situation occurs from time to time...

Hi I was trying to get some help with this problem I’m having in my house , I recently did some remodeling in my home and decided to put a dedicated sercuit for each of my bedroom because before they where all jumped together I also added new lighting to my kitchen and added a bedroom to my...

advice needed. late 2004 CRv. 1st setting (lights off) comes on automatic here in norway when i turn the ignition on. all lights work in that setting. 2nd setting nothing works and that fuse blows everytime i turn to that setting. 3rd setting front dipped or high work but no back lights work...

Hello all, Our Fridgemaster MTRZ110 freezer is, I think, playing silly bu??gers. Certain foods freeze as expected, ie rock solid, others not so. In all my years I've never known a freezer to fail, (there's always time though) But, as above, it's working fine except on the odd item, ie pre-packed...

Hi there I wonder if you can help me please? I have a problem with the drivers side rear lights on my (2007) Audi A6. (includes taillight, reverse light, brake light and indicator.) All other lights are working perfectly. I am baffled because – when I’m stationary – before setting off – all of...

Hello, I’m not an electrician and I have a question in relation to Dimplex Duo300n. Some background information: a couple of months ago I have moved into the property where those heaters are in place (there is 5 of them). The people who used to live in this apartment before, used RXPW4 control...

Hi I've had an electrician fit a new set of led recessed ceilings lights in my bathroom including one which is in my shower cubical. When he has taking the old lights out some of the ceiling came way and he has told me I need to fill the gaps around the light fitting in the shower. I just...

I bought a led light about a week ago. Everything works but there is a problem. The light is sequentially illuminated. I mean (Off - Warm - Cold - Natural - Off ). But I just want to use warm light. I have to wave my hand at the sensor three times to turn off the light. My question is how can I...