I was wondering if anyone else has wired one of these. I just need a big fan for the local football club and asked for one with a pullswitch. Yes nice and easy Switched Fused Spur already there, made hole bigger fitted it, I must say a well thought out bit of kit, until the easy bit LNE, or so I...
Hi all, I am currently updating my ecs card from apprentice to electrician. However when going through the application online it says I must supply a copy of my JIB409 form. I’ve never seen this jib form before but I’m aware you can download the form of jib’s website, but who do I get to fill...
Hello to all from germany,
i have here a Fluke 6500 appliance tester. Most of the keys don't work. As i opened the case there was a smd diode D8 on the logic board clearly defective.
Perhaps there is a service manual or some circuit diagrams for this tester out there where i can see what type...
So the other day a closet light and bathroom light (share a wall) wouldnt come on. The outlets work but no lights. Yesterday they started working again but now my bedroom lights wont come on. Ceiling fan works and outlets work but no lights. Can anyone help?
Lightning either struck my house or close enough that it created a major power surge in my house. It was strong enough that it wrecked an internet modem, 4 DirecTV receivers, 3 TVs, a garage door opener, and a wireless home phone set. It also caused a gfi breaker in the electrical panel to...
I have a recently new to me 2008 Volvo xc70. After a day or so I noticed the main (high) beam wasn't working. At first I suspected blown lamps so I inspected and they seemed fine. Replaced fuse and all was good for a day, fuse blew again. Replaced lamps as a next step and replaced fuse. Lasted a...
Please help!
We’ve recently developed an issue with our lights in the bathroom. The ceiling is a false ceiling and there are 6 spotlights in the false ceiling. The spotlights take the lightbulbs I’ve attached as a picture (Led Gu10 5.5W Warm White 2700K). Having replaced the bulbs, we now have...
Hi all
I have a customer having issues with their Blupont A72 DVR system.
System is plugged in, cameras working and confirmed recording. I'm trying to connect to their broadband so that I can set up mobile access to the camera feed. The system is in the attic and uses plug in network...
I first had issues about 6 months ago with my second hand treadmill tripping the ring part of the way into a session, since then I've sent off my controller board to treadmill doctor co uk. He repaired the board and sent it back after approximately a month.
Since then I've had the a dedicated...
Hi bit of a strange one as load is put on my electrical system the resistance across body earth increases if I measure negative battery lead resistance it rises from 0.1 Ohm to about 10Ohms
Any ideas how to fix
Cheers
Dave
Hello does anyone use the iCertifi software
When I enter the type of mcb for example
Type b 60898 32a it automatically comes up with 1.40 Max ZS I know it only slightly out but if bs7671 says its 1.37 that’s what it is
And you can’t manually change it .
I’ve got a assessment soon and don’t...
Alright lads, new here as looking for some advice on a fault I've never come across and can't pinpoint..
Basically Got LED LIGHTS on compatible dimmers etc...problem I have is now and again they flicker....and I can hear a sound in fuse board as if there's an arc? But there are no loose...
Hi all, hope i can get a bit of help here.
I have a dust extract in my shed which i use when i am turning. This morning i went to switch it on and it blew the 13A fuse, i replaced it hoping the fuse was at fault which it wasn't, well i had to try.
The motor plate 230v, 13amp, 2 pole, single...
I get regular work from a student landlord. In one of his properties the shower isolator switch has burnt out on the feed side several times. I've replaced the switch twice (last time with an MK) and the shower's also been replaced. Insulation resistance on the circuit is >500 and the MCB...
Hi there, new to the forum so be gentle!
We live in a second floor flat above a bakery shop. The shop has plenty of machinery including large freezers that run all night. Recently we have noticed a reasonably high pitched electrical buzz coming from one wall in our flat. Across multiple rooms...
Hi. I fitted a new shower yesterday but it's not working. I don't know what's going on with it but it's strange. The old one is probably about 15 - 20 years old and before I fitted the new one I tested (with an electricians screwdriver) the black and red cables and they were both live. I...
Hi, my names Ric. (Apologises for the essay)
Im new here but with only one question, or problem!
Ive purchased an RGB LED strip to go behind my TV and to avoid bending the strip round the 4 corners of the TV, Ive also purchased L Shape RGB Strip Connectors.
Now since purchasing Ive noticed...
Hopefully someone who has had previous experience can advise.
My MFT 1552 has not been calibrated in a while (as I only use it for fault basic finding in industrial sector)
However it has started playing up .... it is absolutely fine on voltage continuity etc .... but giving spurious readings...
Hello I am hoping someone can help me please.
I am having problems with a motor on my home made 2 x 72" belt grinder
This is the motor
I have it wired via a DOL motor starter.
Recently it stopped running under load, once I removed the grinding belt the motor would stutter and my main drive...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc