I'm building a new property consisting of 4 sperate discrete buildings, all roughly in a straight line. My question: Is there any advantage to connecting the buildings supply in a ring rather than just daisy-chaining them (i.e. radial)?
I was planning to run a single 1 AWG backbone supply up...
Is a 20A 2.5mm radial sufficient for 2 sockets in a utility room? Will be a tumble dryer/washing machine plugged in and a spare socket used for a Hoover occasionally.
Just a quick one
When you see two lines on one MCB that could be either a ring or two radials.
The only way to determine which is through testing. Is that true?
Are there any best practices regarding this?
For example, would you ever see three lines on an MCB? One ring, one radial? Or three...
Hi. I will soon be wiring up my summer house. My plan is to run 10mm2 SWA from spare 50A breaker on my house consumer unit (approx 20m) to a 40A garage consumer unit with 6A MCB for 1.5mm2 lighting circuit and 32A for 2.5mm2 RFC. I plan to have 5 double sockets which will have heater, TV and...
Hi.
I have a radial circuit supplying electricity to the garage (part of the house). It's on a 20amp breaker, uses 2.5mm cable. It currently only supplies a single socket. Before anyone asks, its 100% a radial circuit. 6 months ago I had an electrician install a new consumer unit, and the...
I have a dedicated radial from the consumer unit to my conservatory. This was installed using 4mm twin and earth as it gives the option to use multiple electric heaters on a 32amp breaker if needed. The circuit consists 4 double sockets plus one single socket on the end, in a weatherproofed...
I have an old DeWalt 721 Radial Arm saw that recently stopped working. Initially I thought this was because one of the Start / Stop buttons disintegrated (came unscrewed) and spread its workings all over the floor. I subsequently changed both the switches like for like. (Rafi 1.10001)...
Hi I’m currently wiring my upstairs sockets on a 2.5 T&E protected by a 20A mcb do you think I will get nuisance trip due to the small size mcb or would you recommend making it a ring and using a 32A mcb. I don’t like rings so tried to stay away just I had some spare 2.5 but probably should have...
Hi everyone,
Hope everyone is keeping well.
At a property Fault finding prior to consumer unit upgrade.
Amazing that some bright spark thought it be a good idea to use the Cpc as a neutral And create a pen conducter.
Anyway,
Have a fault on a ring/radial circuit,
Tested end to end on what I...
My shed is only 5 Meters from my house, i will run a SWA cable from existing consumer unit to a shed consumer unit which will have 3 circuits for Sockets,Light and a 7.5Kw shower unit all i need to know is will a 16 Amp MCB be sufficient for the socket Radial circuit for 4 Double sockets
Good morning I wonder if I could have some confirmation in regards to a radial circuit.
I have been showing apprentices different methods if wiring ring and radial circuits.
I wish to continue this next week.
I can not see any regulation not permitting the drawing enclosed, I would just like...
Hi
Im Looking for some advice on compliance as its a bit of a gray area
Kitchen currently has 13a FCU fed from ring main and 2.5mm lsf to single gang skt for washing machine.
Want to change this to
20a DP switch and spur off the single gang socket for washing machine and fit second single...
I have a 2.5mm supply in a loft and from this i have it going to a FCU which I then have my lighting mains for a switch coming from the load side of FCU , I then go from the FCU to 4 different sockets and then last in line I have to connect to another FCU for the bathroom heater downstairs , is...
Hi all,
After some advice here to settle my mind, is there any regulations to limit the number of sockets on a 20A 2.5mm radial? Reading regulation 433.1 i know it states 50m² floor area, but i can't seem to find anything about the number of sockets? Or is it just the total load that...
Hi,
I've recently had a storage heater installed. This was installed in a location that didn't have an off-peak supply.
After some investigation, the electrician moved some wires in the fuse box, to make one of the plugs an off-peak supply. However, this has now impacted: 1 x towel heater in...
So I'm back to work after the bank holiday and I've been asked to install a couple of sockets so they can plug this big beast of a ups system into it.
Currently they have about 5 extension leads all linked to gather supplying it ?
I've never worked on a three phase board before but I will...
Hi I have just moved into a 1960's terraced house that is extremely lacking in the socket outlet department...
It appears that a more modern CU has been installed within the last 5 years and their is a 6mm T&E coming out the back which I have traced to be running into the loft - and the house...
Hello
I am new on this website and first want to say hello to everyone. We moved to a house with old night storage heaters. We had to replace one in our bedroom this winter. The new electric radiator is 1,1kw with a plug. Night storage were hard wired 2,5mm cable with 16a mcb on night economy 7...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc