I did a survey of a larger detatched house today. A poor prospect due to shading from 20m high trees and surrounding houses. Also has lack of suitable roof space.
Real shocker was current electricity consumption. 12,000kWh/a!!!!!!! I would have considered 6000 on the high side. They have a...
Hi Again Guys,
I've just wired a garage unit and have fed It from a 32A MCB from the main cu in the house, so its a new circuit. I have tested the new unit and all is fine. The question I have is.. Do I have to test all circuits in the original cu as well and record results on the same test...
Hi, Guys,when measuring PFC-PSCC on 3 phase supplies,I know that you test between live conductors L1-L2, L1-L3, L2-L3 and then all 3 to Neutral and note lowest reading obtained. Then all 3 phases ( is that right term for C&G? ) to earth. Then neutral to earth and lowest reading obtained recorded...
Hi guys please bear with me as I am new to the electrical game
I have done a private job and run a garage board to a shed with a six mm amoured fone all relevant test on the curcuits
And done a zs at db but do I have to r1 r2 the sub mains to put on the test results or is tbis not needed and...
Recently came across a 6 terminal 20Amp junction box with 12 T&E cables coming out of it and an additional chocy block inside! Is that a record? It was being used as the only distribution box for the upstairs lighting of a 3 bed semi.
I wanted to fit a 13th but the earth terminal wasn't having...
I will be installing a new Ring main for a kitchen install and have come across a cut-out that is totally new to me.
Has anyone seen one of these..and how do I record its details on my Certificate.
I'm testing a car park lighting circuit at 200m long. 4mm singles to first point at about 100m and then reduces down to 2.5mm. Trunking used as additional CPC to reduce Zs values. How would you record that on a test sheet? And is there a regulation about downsizing?
robhawk
Thread
cable
circuit
first
lighting
lighting circuit
long
record
sheet
sizing
I was doing a fuse board update the other day and normally I use duel RCD boards with mcb s but instead I used separate Rcbos due to the customer specifying these. I prefer fitting Rcbos due to just that one circuit is disrupted when there is a fault.
when quoting for the job I carry out a...
Hello, all. I have been a member here for over five years and log in most days, but it appears that I have never posted anything (following a nudge from Dan). Probably because I have nothing much of value to add to the discussions.
I find the forum a valuable source of information, particularly...
Hi Guys
I've just completed my first 3 phase installation. A 3 phase CU (Proteus) in a church extension. There are 12 x 230V circuits feeding sockets , lights, heaters, etc.
1. Do you record all circuit test results on the same page or use one page for each phase?
2. Do you record Zs at DB...
I frequently get asked to inspect a light fitting or a socket to ensure safety. Customer is asking for a cert to confirm. How can I record to give customer a cert without providing a EIC cert.
depending on the job I usually test ze zs and IR and ring continuity if required.
i use to visit loads...
Hi can someone please endorse or recommend a data logger to monitor and record refrigeration compressor on/off starts and a data logger to measure and record KWH. Thanks
What is the best way to confirm r2 and R1+R2 when the circuit is routed in conduit and this is used as the cpc?
I have used wander lead and got continuity at all points on the circuit for the cpc.
rn and r1 are within 0.03 of each other so no problem there.
just how to confirm that the...
kevinfran
Thread
circuit
conduit
confirm
cpc
electricians' talk
record
rfc
using
verification
I am used to niceic forms so please bear with me! In the insulation resistance section it only has two fields for recording details which are live -live and live to earth, surly I have to record more than a live to earth for a radial what about neutral values!!
Rauer
Thread
certs
earth
electricians' talk
installation
neutral
record
Got a call a couple of days ago to a boiler which had been looked at by a gas guy who advised of an earth fault and that he had isolated it. So I bowled up today, there was a VOELCB right by the BS3036 CU which had excessive charring on it, some fuse carriers were crumbling others were cracked...
just reading a post by jaysparks involving music, and it got me thinking- whats the first record/song you bought? mine was god gave rock"n"roll to you by kiss. think it was late 80s when it was sound track to bill and ted. not that embarrassing. what about you lot?
Hi guys its a most random one but worth a shot. Just looking to get my old vinyl out and bought a cheap late 60's record player, on flea bay but
Thing is guy now told me it got 2 pin. He said it was a set with amp the 2 pin are the flat type. Now am i correct in saying this is NOT old US?
Any...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc