remote | Page 4

remote

Recent contents View information Top users
  1. T

    Honeywell G4 Accenta Remote Keypad

    Hi all, just powered up a G4 Accenta and I'm having trouble with the remote keypad. The red and green indicator led's are lighting up,but thats it. Nothing on the lcd display,no backlighting and no response to putting default code (0123) in. This is a brand new system,straight out the box. I've...
  2. T

    Honeywell Accenta G4 Remote Keypad problem

    Hi all, just powered up a G4 Accenta and I'm having trouble with the remote keypad. The red and green indicator led's are lighting up,but thats it. Nothing on the lcd display,no backlighting and no response to putting default code (0123) in. This is a brand new system,straight out the box. I've...
  3. A

    Shunt trip in a domestic CU? Looking for a complaint way of remotely switching off power

    Hi. A thought of a domestic fire in my house terrifies me, so I installed a really sophisticated fire alarm in my house. This system optionally can even turn off the gas valve (it has a motorized arm which is installed on the main valve) and switch off electricity in case if the fire is detected...
  4. B

    5 Wires to go - Help required to remote fire up the boiler

    Hello all, I've found myself left with a small amount of wiring to do to complete an installation. It's a Heatmister UH8-RF unit being wired to a Drayton 2 way valve. The boiler engineer has done 95% of the wiring and has not gone sick long term. I'm left with only the remote 'fire the boiler...
  5. Andy78

    Isolator when inverter is remote from consumer unit

    I have never done PV but a customer has had a system installed and has a few issues with it, most of which are being sorted out. I have a question, should an isolator be positioned next to the CU when the inverter is in the loft ? I have never seen one without, and had advice from other...
  6. Jay89

    Virgin remote signal extender

    Hi all, I’m after the virgin equivalent of sky’s magic eye. I have a TV to be installed up on the wall of a clients kitchen, breakfast bar below and was hoping to site the virgin box in the cupboard below the worktop. Does anyone have any recommendations? Thanks in advance
  7. L

    Pyronix 280 remote setup help

    Hi if any one could help me with this one i would like to know how In the setting to setup to allow rsd to remote connect into the system where to I need to go to do this thanks
  8. TonyJohnson

    Remote colour changing light bulbs and neutral fault

    Adding a socket to a ring today, the socket fitted correctly, the ring with correct continuity and IR results OK but.... Plugging in the socket tester brought up a neutral fault?? The house has remote control lamps that change colour, can this electronic device effect the neutrals.. it seems to?
  9. J

    Lightswitch transmitter with remote

    customer i am installing soffit lights for wants to control the lights by remote, so i am thinking having the lights connected to the transmitter then a on off remote control, has anyone used these before and can recommend any ?
  10. P

    Luxna remote control downlights

    Anyone know if these are any good...?
  11. N

    Light switch wiring for rf433 remote switch

    Hello all, My first post on this forums. I've installed couple of those remote control (rf433) light switches in my house but having trouble with the wiring in my bedroom. Most of the other switches had live and neutral but my room switch (1 way 1 gang) has a different wiring, picture...
  12. Gavin John Hyde

    Product recall of remote control plug adaptors

    Had an email pop up in my inbox announcing a product recall of some remote control plug adaptors. They were sold in B and Q until recently. Have attached the email in a pdf below. In all honesty I am surprised not to have more of these emails given the poor quality and cheap tat a lot of the diy...
  13. J

    PIR switch remote overriding

    Hey guys, On a job at the moment where the customer wants an LED flood on the end of a farm building, Seems straight forward but he has now decided he would like the light to be PIR operated, Manual override inside the building, AND a remote to switch the light on from his house about 10-15...
  14. S

    Remote control 2 way switching.

    I've seen a couple of kits for doing this advertised. Any recommendations or products to avoid?
  15. D

    Remote control lighting systems

    Morning All, I'm looking to control outside floodlights from a remote device (similar to an auto garage door for example). They are presently switched on from indoors and would like to keep that facility in addition to the R/C device. I've looked at Wise Controls from Focus SB and they seem...
  16. kevyn

    Remote Start/Em Stop button for generator issue

    Hi I have been presented with an interesting problem with a generator: 3 phase diesel generator with remote start/em stop inside workshop, when generator is started with the remote button it will only run for 5 minutes maximum. Generator will run all day if switched on at generator itself. It...
  17. P

    Hoist control wiring help please!!

    Hello all, I'm hoping some clever person can please help me... I have an electric hoist set up and I would like to have another one to lift at the other end. I don't really want to operate 2 remotes so I want to wire them both into a terminal block and then into 1 remote.... That sounded simple...
  18. Bob Geldoff1234

    Remote controlled light switch

    Could anyone recommend a remote controlled light switch? It must be able to dim and switch up to 320 watts,preferably not be too deep at the back and not cost a fortune.Also there is no neutral at the switch so it would have to be a live in and live out one. The ones i have looked at on Ebay...
  19. rolyberkin

    Screwfix or TLC LED PIR

    Hi All Not bought an LED floodlight for a while, looking for a mid priced recommendation has anyone any recent experiences fitting either the Screwfix LAP or Luceco brands or the LEDlite from TLC? Thanks.
  20. S

    Portable tool station electrics, Saftey advice help

    Hi all, I am building a portable workstation to hold 4 power tools IE: Router, Saw, Disc sander (Drill powered), Small Drill Press. The idea I would ideally like is for each unit to only be powered at any on time without the others being able to switch on until the one in use is switched...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top