roller | Page 2

roller

Recent contents View information Top users
  1. Dan

    Cheap large roller toolbox!

    Just found this on fleebay http://www.ebay.co.uk/itm/FoxHunter-Plastic-Mobile-Roller-Work-Shop-Chest-Trolley-Storage-Tool-Box-Toolbox-/111274440959?var=&epid=1012664579&hash=item19e87938ff:m:mAAVN7cQSXAb7C7udFL98WA Selling fast. 40% off. Not sure you could climb on them, but they see a cheap...
  2. the pict

    Jack not roller skate

    Where can I buy a proper car jack other than the bloody useless toys on ebay, you know the ones they are about as big as a roller skate and just about as much use, these things of which I have 2, one failed dramatically going down like a shot rat, the other has a mindless want to invert itself...
  3. J

    Roller shutter door motor wiring diagram

    Hi We are looking to replace an existing roller shutter door motor with the below Garog motor and wondered if anyone had a wiring diagram for this? Make: Garog Type: ULA25EE V 400 A 1.0 KW 0.5 RPM 28 PH 3 HZ 50 IP 44
  4. H

    Roller Shutter door connections?

    Hi I have been called to a job recently to install a up and down switch for a small roller shutter door. Motor and control unit all there but previous owner had ripped the switch out. So just left with a few cables not connected to anything and empty connections. I havent done a roller door...
  5. G

    Roller shutters - emergency stop buttons

    Had a conversation with a roller shutter installation comapny today. They have installed their electric shutters on a project we are working on. They have installed a key switch up/down button. No emergency stop button. I said to the PC today that there should be one installed. The answer I...
  6. B

    Roller garage door problem

    My neighbour has a problem with his Securoglide Compact electric roller shutter door. When using either the wall mounted control box or remote control it closes OK without any problem but when attempting to raise it using either controls it stops after a few seconds and starts again...
  7. M

    Industrial roller shutter door help

    Hi guys iv got a indutrial roller shutter door at work which will only go up about 2 meters and stops in the same position everytime when you push the up but it will not go any higher but can be lowered n re hightened to the same position and cuts out. Does anybody have an idea what this could...
  8. J

    Check out me cable roller

    Made with two 90 degree angles boxes, 20 and 25 mm conduit with couplers and bushes, ooo yer.
  9. I

    roller door controls

    not sure but is that the limit switches that i am pointing out , company says the door needs a new motor , when i try and open the door that unit keeps buzzing and flashing , would a faulty motor cause it to do that or could it just be that unit thats faulty
  10. B

    3-phase Roller Shutter Door - Opinions please

    Hi guys, recently been given a job to supply power to a 3-phase roller shutter motor in a warehouse. The cable path is to follow the a-frames of the roof on 50mm tray with girder clips (to span the warehouse) then tray along the wall to the motor.. must i use SWA? its a 75 metre run in total...
  11. S

    roller shutter door

    Hello guys called out to a fault on a roller shutter door when you press the button to go either up or down and hold for a while then release the door will continue for a few seconds if you press the button and release straight away the door stops instantly as It should would this be the relay...
  12. N

    Key switch into remote roller shutter system issue

    Hi, currently updating the studio entrance system. The roller shutter previously ran on a keyed switch. Standard 3 core in to 4 core out to motor. An RC1000 unit has now been put in place, with the motor now being directly wired into this, as well as all other controls. The problem I have...
  13. I

    Roller Shutter Limit Switches

    Hi, Does anyone have a wiring diagram of a typical roller shutter limit switch config. My shutter is working but I would like to see what the switches are actually telling the board. I could get a ladder out and measure the voltage on the screws but a nice diagram would be better ;-)
  14. 1

    Security Roller Shutter doors on 1300VA UPS

    Hello, I have been asked by a customer to provide a backup power supply for his roller shutter doors that protect his property. The motors that supply the shutter doors are a maximum 600W 230V AC (2.6A or 600VA) I have never been asked to provide a UPS for anything motor related. The need...
  15. J

    roller shutters

    Hi Guys, does anyone know of any specific codes of practice, standards or wiring diagrams I can reference for wiring power and manual control switches to multiple roller shutters covering office windows. Im attempting to resolve a contractual dispute and need evidence based information...
  16. Hellmooth

    Roller shutter door switch

    Hi just a quick question.......I have a switch which is being used for a roller shutter door, it simply has 1 wire for common and 1 each for up and down. I belled out between common and both directions to check it was working fine which it was, so it is working how it should.........it might...
  17. R

    3 phase Conveyor drum motor?

    Hi guys, anyone know where I can source a new 3 phase conveyor drum with quick deliver? thanks
  18. W

    Roller shutter motor replacement

    Has anyone had to replace a garage roller shutter motor before are they fairly straight forward to do?
  19. rmaynard

    can anyone suggest a UPS for a roller shutter

    as above, has been asked to quote and install a UPS device for a security shutter at my local doctors surgery. Problem they have is they are looked out if theres a power cut as there is no manual crank. ideas please
  20. R

    industrial roller shutter door.

    A friend of mine has a 3phase roller door. Under normal circumstances you press the up button and it opens and continues to go up untill the limiter switch kicks in. When it comes down you have to press and hold the down button. I guess this is for safety reasons. The up button has stopped...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top