hi all
i am new member and need help.I have to connect 4 plugs to one rotary switch so that one plug can be active at a time and three remain disconnected and when rotary switch moved to position 2 second plug became active and other three inactive.Please advise whether i need 4pole 4postion...
This is a follow up to a thread I started yesterday.
I have been working all day installing a hot tub situated outside on a patio slabbed deck.
Contrary to what I was told, it was TN-C-S supply so here is how I have wired it.
From Henly blocks - 25mm tails to a one way board (Main Sw RCCB -...
devonsparky
Thread
connected
earth
electricians' talk
hot tub
installation
rotary
Ive been asked to install a circuit which will supply a compressor. The customer states that the compressor requires a 30A fuse at the CU (according to manufacturers instructions) and ive told him that it will need a switching device for isolation and mechanical maintenance.
What im a little...
Greetings.
I have a Megger 1552 and the rotary selector switch seems to be getting a bit tired.
I sometimes have trouble getting it to select the function I want be it RCD test or resistance etc.
My question is has anyone ever stripped one down and cleaned the terminals behind the rotary...
Ryobi one plus 18v cordless kit as below.
Hammer drill
Angle drill
Rotary Cutter
Radio
Torch
3 batteries
1 charger
big ryobi carrybag 22 inch open top reinforced one.
All in a nice matching blue colour.
It has all had some use, but they are still in top condition and work fine, no defects...
Is it an MCS requirement for both the AC isolators to be of the rotary type and to be lockable in the OFF position and where can I find details of this, anyone has a link???:dizzy2::dizzy2:
can anyone tell me if there is a regulation for the colour of isolator handles? I have just taken delivery of some 20A AC surface mounted rotary isolators with grey and black handles, I always thought they should be Red & Yellow handles??????
TJLinks
Thread
aus
electricians' talk
isolator
rotaryrotary isolator
Evening Chaps....
I'm after a 3 position switch so that I can switch a PIR between the following : perm ON / perm OFF / PIR mode
Not a pulse one though.
Any ideas, is there such a thing ?
Cheers Sy
Hi,
I'm currently wiring an outside oil boiler and have sited a FCU on the inside wall with a 2.5 t+e to an adapt box and from there, a braided flex to the boiler.
Does it need a rotary switch instead of the adapt box?
devonsparky
Thread
boiler
electricians' talk
isolation
means
oil
outside
rotary
switch
Hi, I was asked today by a potential customer about installing one of the boost energy range of phase converters.
Is there anyone out there with any knowledge of these devices?
Cheers
When its come to 4 pole rotary isolators, do most of you use one brand or whatever is in stock at the time of ordering.
Fitted 2 Gewiss ones today and thought they'd be good to work with, how wrong was I?
No space in em at all, the cheaper ones from Chint and Europa seem just as good but loads...
Does any where still do the old cast metal rotary outdoor light switches normally gray.
I have been asked to replace one thats not working but he wants one the same as outhers.
Bought 21st December 2010 (receipt included giving warranty until Dec 2012) Used once. Unfortunatly I bought this at the same time as a TE7 so it doesn't really get used. I was going to sell the TE7 but am using the batteries on my saw. It is in excellent condition, I would say as new apart from...
Hi everyone
Im just wondering if anyone has one of these drills and can reccomend it, im looking at purchasing one for domestic work. Also does anyone no the difference between this drill and makita model BHR241RFE as they look very similar.
cheers
Ash
I've posted a similar question before but lack of funds prevented me buying.
After searching round I think I've narrowed it down to one of the following two drills. I have no experience with either make, I've always stuck with dewalt.
Can anybody recommend one over the other?
Option 1
Option 2
MUFC1999
Thread
again
batteries
drill
electricians' talk
garden
hammer
panasonic
rotary
sds
Hi guys,
looking to buy some 110v tools, thinking they are better than battery powered tools.
In particular want a jigsaw and a 2kg rotary hammer drill, can anyone recommend any, been looking at mikita as they always seem to get good reviews?
Thanks guys
Craig
Hi guys looking for help with testing three phase for correct rotation.
I have a 2 probe voltage tester with left or right rotation indicator.
Probes are marked L1 and L2.
Would I be right in thinking that to test rotation I would need to test as follows.
Probe L1 to phase 1 probe L2 to phase...
sjm
Thread
electricians' talk
help
phase
probe
rotary
rotation
testing
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc