evening all, i swopped an 8 ft florry switched by said sensor for two 5 watt led bulkheads (hispec) and the sensors now don.t switch the led's off even when turned the time right down, there are two sensors but the other one is just connected to an old florry which is being swopped tomorrow for...
I'm looking at fitting a sensor in ducting that carried airborne paper dust to signal when there is a blockage. I'll locate it just before the usual place where it blocks up. I would like to avoid an optical device, as it would require regular cleaning, I'm thinking of a capacitive type that...
Hello all,
Firstly, as a DIY'er I would have put this in that forum but for some reason I can't seem to post to it.
I have installed a LUXOMAT Indoor 180/R-2W UK on my landing to replace the switch :
http://luxomat.com/en/pdf/en/datasheet/92616_92615.pdf
It appears to work, when I walk up to...
Hi all
I've recently moved into our new house and i'm puzzled at what this switch is in the porch.
The switch puts on the porch light and an exterior light, but i not sure what that is on the left under the slider.
I thought it was a light sensor but it does nothing.
please see attached...
Hi everyone.
I'm new and after some advise please
I am putting security lights up at my house. They are the sensor type. They didn't come with the cable so I went to my diy store and asked for the right cable to use.
I have wired up the light as per instructions.
The other end I...
Sonia Dowsett
Thread
brown
cable
help
light
lights
security
sensor
wiring
wiring help
yellow
Hi All
This question should probably be in the DIY section but it appears to be locked and won't allow me to post a new message on there so....
I am trying to get a PIR sensor working in a house I moved into but I cannot find any advice online.
This sensor was set up by the previous owner in...
Afternoon all
I have a DOL starter with 415 coil. Basically I've been asked to put a selector switch in so that a proximity sensor can control the DOL starter.
Could anyone provide me with a wiring diagram on how to do this?
Many Thanks
Hello,
I have a Nissa xtrail (petrol) that is refusing to start... It's a long story but ...two things happened more or less at the same time - 1. Timing chain jumped some teeth due to failed tensioner & 2. Crank Pos sensor developed a fault which somehow melted the connector block!.
Timing...
Just wondering if anyone has had problems with 2D 4 pin light bulbs constantly blowing. In a boarding house there are a total of 24 every 3 on a motion sensor and was informed before i left today to have a quick look tomorrow as they are changing about 5 bulbs a week! All the circuits are rated...
Hi guys. Just a quick one. Doing the electrical work on an extension and they used to have a garden shed with an alarm sensor in it. I want to remove the sensor from the system but wondering what's the correct way to do it. The sensor has a +,-, tamper and N.C in it. So do I just bridge out that...
Hi new on here looking for a bit of advice. I can find pir sensors that will allow lights to come on and stay on for a specific amount of time (1-8 hours) and then switch to motion sensor till dawn but not to switch over at a specific time.
Any help gratefully received
East1
Thread
customer
dusk
lighting
lights
pir
sensor
switch
wants
Customer has asked for a right awkward one - they want bathroom lighting installed as below
9 x LED GU10 Downlights
Mirror Light
LED Plinth Lighting
In-Line Fan
OK so straightforward enough until they have requested no switch but an occupancy sensor, but not just any occupancy sensor!
They...
Hi all. Firstly sorry if this is posted in the wrong section - I'm new so please be gentle! :)
A few years ago I bought an LED bathroom mirror from the Bay of E and it's been working fine until now. It has two rows of LEDs, a heat pad and motion sensor switch. I've popped the back off and can...
brbrbr
Thread
bathroom
don't
driver
led
mirror
sensor
switch
terminals
Hi, All I got great advice on here re solar pv (which is working very very well) a couple of years back and I am looking at some enhancements and things seem to have moved on in the metering dept and I was looking at the Chorus PV solar monitoring system.
In particular how it works by...
I live near the coast & have had 2 metallic security lights.
These have each corroded to the extent that the case could not be opened when the light failed.
Can anyone suggest a non metallic security light fitting?
Thanks
Evening all, 1st fixing a job at the moment and the client is having 6x LED Aurrora sola IP65 down lights installed in the soffit at the front of the house, the road is less than 3m from the front door and soffit obviously, they want them to be triggered by a sensor, so i suggested fitting a...
D.A.B_SOULTIONS
Thread
distance
front
house
pir
sensor
short
soffit
switch
Alright Chaps, I've a long corridor in an office block that I'm fitting some 360 PIR sensors to the lighting, I need the lights to come on all at once for all locations of the corridor but there is a blind spot so I'll need to fit 2 sensors... Is there a sensor out there that you can link...
Hello all..
The customer wants his garden light to switch on the moment he walks into the garden, the sensor is around 12 meters away and it doesn't switch the light until he is half way up the garden. There is nowhere nearer I can locate the PIR.
I realise screwfix/toolstation have PIR's...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc