In need of a replacement lens for a LSI Lightron Inc. Series STF recessed, 4 tube, fluorescent fixture. LSI was bought out a while back and are mainly LED fixtures now. Even the rep. I was working with from the company was not able to find anything like it.
I have run new cables, segregated the SDI cable running back, so the LED will switch independently and have also installed a capacitor, since I was informed that would be a fix but it bursts light. The picture shows bottom mech with the switch on and bottom mech with the switch off. Thanks so...
I have tried to find info on connecting WS2812B led strips Dat/signal line without any luck. I wondered if it was ok to connect the dat/signal line in parallel to 2 existing led strips from the controller or does it have to be in series?
I am installing recessed LED lights wired in series. My question is, the last light in the series will not have a ground to connect to...what is the solution?
Hi all
I am a newbie from Australia to this great forum.
I need some advise with wiring up a dimmer and switch for my LED Down lights in series.
I have run a mock up from the extension cord with some success. But still have issues.
The dimmer instructions diagram indicates one red...
I recently fixed a fault on a lighting circuit. The fault became apparent after some work I had carried out - I rewired part of the circuit for an ensuite refit, plus some additions to other circuits supplied by the same CU. I needed to provide RCD protection to the circuits that I had worked...
There doesn't appear to be an ionisation detector available for the Ei Electronics (Aico) 3000 series alarm range. Or does anyone know of one?
Basically there was a house which was a HMO at one time, but was converted to a single family rented property. For some reason the fire alarm panel was...
Hi folks, just a query about having two RCDs in series. I want to have installed three new external 2 gang 13 amp SSO to IP66.
I currently have a 100 amp BG CCU installed by an electrician in 2016 with split load and 2 BG 63amp 30mA RCDs labelled ICE/EN 61008. The supply is what we used to...
Where can I find the MPAN on a "Radio Telemeter Series K" meter? Unlike the older meters, this just has a serial number and stores code on it.
I have no way of getting past energy bills but doubt if that would help as the meter has been changed.
ENA requires a 21 digit MPAN. The serial number...
Good evening all. I'm in desperate need in some help please. I recently changed a fuse board with a horstmann radio telemeter series 2a NU077-222, not realising that it is an economy 7 meter.
I'm very confused into the connections of the other tails required to feed a separate fuse board for the...
Hi All
A while ago a customer asked us to move a 1970s single phase corn mill and return it to use.
It had an old series parallel starter with a lever on it ..which we replaced with a crompton controls series 3000 starter...all good and running.
Now they had another ip rated box attached to...
Aico Launch 3000 Series System | Aico Fire and Carbon Monoxide systems
Aico have launched a new alarm system for fire and carbon monoxide detection. As your clients switch on their heating as we come into winter protection against accidents is vital. the 3000 Series is one alarm system for both...
Hi,
Regarding discrimination requirements in regs..
If a second cu is fitted in a shed or outbuilding supplied by an rcd protected way at the main cu then it provides protection at a change of cable size due to the mcbs but that leaves two rcds in series with no discrimination. However is...
Hi everyone,
I was wondering if I could get a little advice on a small project I plan to carry out over the next few weeks.
I plan to install 10x 6w GU10 LED bulbs (fitted inside some suitable outdoor light boxes) on each fence post along a 30 metre garden fence, the lights will be powered...
Hello.
Before I bother a professional with a call out, could I ask for some advice on here.
Our cat managed to dislodge the cut-off fuse on our board, shutting the power off. I pushed it back in and everything's back to normal. But in doing so, it made some rather nasty noises and it doesn't...
my external sounder/bell and LEDs (not flashings) to have no power going to it. Do these boxes have a battery fitted?
The PSU has the correct voltages and fuses are good.
Reason for asking before climbing up to box is because I may need to get scaffolding to reach box.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc