setup | Page 3

setup

Recent contents View information Top users
  1. S

    Advice needed to earthing POE radios Ethernet setup

    Hi, Apologise if this is not the right board to post about this subject and please be patient as I am not a qualified electrician. I am extending internet access between two buildings about 30 meters apart via two Ubiquiti NBE-5AC-16 NanoBeam AC 5GHz 16dBi radios which I prefer them to be...
  2. A

    Current Frequency Counter - Wiring and Setup

    The current frequency counter we ordered on Amazon has just arrived, with a vague and minimal setup manual
  3. M

    Best Meter Setup For Multiple Use Building

    Hi some advice needed please. I am working on a commercial property, originally all one building (Machine Shop) with a 100A 3 phase TT supply incoming. The property is now being split up into multiple units mainly office space with one beauty salon all to be leased out by the landlord. The...
  4. Dan

    What's Your Speaker / Amp Setup?

    I have an Onkyo SR606 with 4 bookshelf speakers (no bass or centre). Just seen this though...
  5. S

    Generator setup and earthing

    Hi all new to the forum and electrican. Working on a plant at the moment where the client is wanting to have two 480volt 60hz three phases motors installed inside there workshop. These motors are going to be fed from a generator as they do not have enough power to feed them off the workshop...
  6. S

    Electrical help needed, DIY, dimmaer wicthes blowing relays on my solar setup.

    Hi All, I wonder if you can help me.... I've been designing my own solar solution recently and built a small example that worked really well. I've taken it into production and working with an electrician friend of mine, here is what we setup: I have a solar panel connected (through a DC...
  7. D

    Urgent Advice please on connection of AC from inverter to quad CSU setup

    Hi All, Many thanks in advance for any advice, I know this is the place to ask:blush5: Basically I am a 'consumer' who's having a pv array fitted and I want to check what the contractor's intending to do. I built my current house so I don't want it going up in flames! Unlikely but I'd rather...
  8. F

    Problem With 2-Way Heater Switch Setup

    Hello everyone! Need as much advice as I can get. This issue has stumbled a few certified electricians. Hopefully, with the wealth of knowledge here, a solution to this can be found. I'm a homeowner and a fairly competent DIYer. My home was meant to be set up to have 2 points of 2-way...
  9. M

    Mi-led controllers

    Hi I am struggling with a 4 zone mi-light controls setup. I have email them but they are useless. Has anyone managed to get one of there colour led wifi controllers working. If no I am will to cut my losses and get another setup. Can anyone recommend a good make Thanks
  10. P

    Upgrade of current setup SouthWest

    Upgrade of current setup. The current setup on my house is 14 Upsolar up240p polycrystalline panels at 105 degrees, feeding into a Fronius igtl3.0 inverter. It is ok but the power drops off after midday so I'd like to expand it. It was put in, in February 2012 so has the higher rate of FIT...
  11. E

    Trying to setup 21 Computer Fans each rated 12 Volts, is this correct setup?

    Hi all, I’m completely new to any kind of electrical work and would be grateful if you guys could confirm my setup to be correct. I’ll try to be as clear as I can: I have 220V coming from my Wall Socket, so I assume I have 220V to use. What I’d like to do is, use the...
  12. E

    Pics of Sonos wall mount setups

    Hi all, After some guidance with a Sonos setup. Looked for a few decent multi room media setups for our home and the Sonos products look right up my street. My question really is how have people run the supplies to the units. I want to give the impression that the units are completely wireless...
  13. S

    What software setup are people using on there testing?

    Hi guys just wondered what you guys are using setup wise for testing, i have been using easycert but not sure I'm that keen on it to be honest, had a play with Certifi and i like the EICR layout and the fact you can add in images to reports? Thoughts? Cheers
  14. J

    Adding to current garage setup via fused spurs

    Hi guys, I'm trying to extend what lighting/sockets I have in my garage. Currently I have a 2.5 t&e coming through the brick to what feeds 1 double socket and 3 tubelights. I'm not sure wether this is spurred off a ring main or is part of a radial circuit from the house. Anyway I want to...
  15. Simonslimline

    Any thoughts on this extractor fan setup!

    In the flat i live in i have an extractor fan in the kitchen that is fed by a 1.0mm2 3core FT&E. The supply comes a fused connection unit off the RFC. The extractor has L SL N CPC. The switched live is terminated on the load side of the FCU, as is the Neutral. The permanent live is terminated...
  16. C

    Trouble-Shooting 2x18W Flourescent setup

    I agreed to take a look at shop sign for a shopkeeper friend. The fitting apparently stopped working form one day to the next. I have checked the following. 1) 240V getting to the fitting. 2) Both starters work fine in another fitting 3) Buzzed all the way round wiring loop with tubes/starters...
  17. C

    caravan park distribution setup

    I've been asked to wire a caravan park up so far the system consists of: connection boxes with each socket on a 16 a trip 30mA rcd SWA to each conn box buried to 600mm+ Incoming supply is t.n.s But....The main distribution board is 3phase so do I have to have the distribution cct on mcbs alone...
  18. M

    Cable TV Setup

    Hi Guys Living in rural Lincolnshire i've not come across Cable TV before, and i'm looking for the full gen on it. So what cable do i need? is it distributed centrally? is it internet and TV? I'm a full scope NICEIC registered contractor and I've got a rewire to do in a town with CATV and the...
  19. M

    SolarEdge Communication Setup

    Guys, Does anyone have experience of setting up communication on SolarEdge inverters? We have just finished our first SolarEdge installation, the inverter and optimisers are generating perfectly but we can't get the inverter to communicate with the online portal. We connected the inverter to...
  20. F

    LS industrial Systems IE-5 VSD Setup

    Hallo Everyone. I don't work with VSD's everyday. I typed this up as I was struggling with the setup. Hope it can help someone. Its just for starting and stopping with a signal. Drive not setup at all for run. Signal wire from key switch must be in terminal P1 and Com to receive signal...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top