Hello. I had a good monitor AORUS AD27QD. Yesterday when i was sleep i left monitor on like always. When i woke in morning there was not power in house. Something tripped breaker/fuse.
When i turn up breaker and power back in,monitor just refused to turn on. So monitor i guess tripped breaker...
Hey,
We are putting in a Honeywell flex alarm. It's all wired in (following the manual). The problem is that all the sensors are coming up as having a short circuit and I can't work out why. I've wired it up with my friend (who is an electrician) and we really can't work out the problem...
Would you divide the 5.13 ohms by 4.
I personally don’t think so.
Also the R1 /Rn short circuit resistances are different from the usual R1 /R2 measurements.
Found those in an electrical book by,that man.
The Zs on this circuit was above the permitted figure,so just had a play around to see if...
Hi, I have lighting in the bathroom plus an extractor fan. There is one switch for the lights and one switch higher up for the fan. I installed a PIR in the bathroom and wnated it to turn both lighting and the fan in parallel to the switch. I fed the PIR from the fan's permanent F and took the...
Hi there
Im reaching out here as I have given up trying and couldn't find a local electrician to help today .
so the issue .
after painting the wall I was try to fit the light switch back into the wall and somehow the com cable touched the metal surround on the wall.
the lighting RCBO...
Could someone shed some light on the following please?
411.3.2.1 implies that the 5s / 0.4s disconnection times only apply to earth faults. I've not found anything else in the regs that suggests they apply to short circuits.
435.5.2 says faults should be disconnected before the fault current...
Hi all,
I do hope you can help me with my 2014 Fiat Fiorino.
I have a short circuit which has stopped the rear tail light and front side light from working. when the lights are on, ignition is on but the engine isn't running the lights work, the lights work whilst the heater plug light is...
Hi all. Seems like a simple fix just need some advice. I was fixing LED strips in the kitchen today. The switch in the kitchen is a 2-gang which powers the LED strips and the ceiling lights.
There are 3 seperate LED strips to go around the kitchen, each connected to an LED driver and power...
Morning All,
Having spent many years gleaning information from you all as a non member I've finally needed to join because, try as I might, I just can't find the answer to this puzzle, so here goes.
I've just installed, replaced really, a TP sub board that's being fed from a Crabtree 60A STD...
Hi all,
I just installed the Nest 3rd gen into my new house, which was a bit of a mess - everything was wired straight into the old Honeywell ST7100 without any sort of junction box. It’s a Y-plan system with a (very old) Glow Worm 35F boiler, a Honeywell V4073A1039 valve and a UnitFive pump...
I've come across a fault at work. Fuse keeps blowing when they put it in. I haven't tested for a while, and so am pretty sure I'm missing some basic steps with the fault finding process.
Small room. 1 emergency fluorescent light fitting, 1 bulkhead emergency fitting.
Fluorescent is plugged into...
hello,
studying for my 2396 exam and i need some help!
Been banging my head against a wall for hours trying to get this one straight in my mind.
The question is as follows:
An electrical installation within a small retail outlet, located in a farm building is to be designed with the...
Anyone able to help on the following...
Short circuit calculation & current carrying capacity of:
50x10mm2 copper busbar
&
80x6mm2 copper busbar
One for the brain boxes..
Hi all.
Advice please. Had a flood 36 ish hours ago where several tens of gallons of water came through kitchen ceiling passing over the kitchen lighting circuit.
The lights (6) are ceiling inset 240 downlights, no transformers. The lights are connected in the circuit with connection blocks and...
Hi. I would like to get a help from this forum electrical engineers. There is the international standard “IEC 60909” for calculations of symmetrical and asymmetrical short circuit currents.
I need to calculate line-to-earth short circuit (circuit 0.4kV) by the software that uses calculation...
Hi Folks,
Ive got an elderly water distiller that packed in a few weeks ago, with a suspected blown heating element (kept tripping the main fuse).
Sent away for new parts, installed them and now it just blows the local fuse, accompanied by a flash and a bang. :(
Ive been over it all with a...
Sorry just learning but with a short circuit.
V=i x r so dosnt that mean that the maximum short circuit in a circuit with even no resistance would be 230 Amps.
How comes I hear of higher currents in faults and breaking capacity for the breakers are 6ka.
Can someone explain a short circuit And a break in a cable when fault finding please what is the meaning of them please. Was fault finding today on test rig
I'm a qualified spark but studying building services engineering at uni and just need a little bit of advice to see if I'm going wrong.
Trying to answer a question where we have a 16A Type B MCB, and a short circuit fault current of 153.37A. From fig 3.4 of regs we can see that for a fault...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc