Hi
My thermostat usually shows a room temp of between 18 and 20 degrees
However occasionally it is displaying FROST MODE and showing low temperatures. Basically when it goes like this we can either have heating on or off with no control which is very annoying!
Can anyone advise, I have...
Hi - went to a client tonight to wire a two way lightwave smart master and slave switch. When connected as stated on instructions the light was permanently on and when the switch was actually pressed on the bulb flickered. When I checked voltage across the live and switch live terminals it...
I want to talk about the context to this first, I'm in my first year at college studying level 2 electrical installation and for Christmas my family got me a toolkit which had some tools , multimeter and a soldering iron. They didn't really know much about things like that and they wanted it to...
hi everyone, hopefully you can help.
I have a 4kw solar panel system and just noticed a drop in how many kw it’s producing. I checked the inverter ( fronius primo ) and the lcd is showing low dc input on string 1.
Any ideas of what the problem could be ?
Even if I could narrow it down to what...
When I turn my oven on and touch a mains tester screwdriver against the casing it illuminates. It’s only happens when the heating element is on.
The oven heats well and shows no other signs of issues. The casing is clearly not properly live as it’s touched all the time.
Is this something to...
This popper up on my twitter feed tonight, shows a house gutted in Greater London from fire due to a consumer unit fire.... Make sure you double check your terminations and installs and it can almost always be avoided if you do things properly.
Hi. Penny for a thought anyone. I'm still in holiday mode from yesterday...
Just been to a house after a plumber refused to touch the boiler (not before getting his £200 call out charge) saying there was an electrical fault and showing the customer his voltage pen light up on the water pipes &...
I was checking polarity using multimeter on some 12v DC adaptors I have.
Doing this showed me the voltage. Here on my readings:
12V DC 200ma = 19V
12V DC 500ma = 16V
12V DC 1000ma = 14V
Question 1): Why are they not showing 12V? Is this because all happen to be unregulated?
Question 2): Why...
Hi all.
I've just had my house in France upgraded to single phase.
I've bought a consumer unit as i only want a basic set up (minimal electric is used in my house!) and am going to put it in myself.
I have a book which teaches you how to wire up.
The consumer unit comes pre-packed with one...
pipunch
Thread
book
bottom
breaker
first
french
rcd's
showing
shows
type
wired
wiring
hi i am replacing a consumer unit over and came across a strange problem with the neutrals when i isolated the old consumer unit. When isolated from supply im still getting 240v between incoming live and out going neutral. I have disconnected all neutrals from block (which clears it from...
Not making excuses, probably a for gone conclusion, as I 'm not a fan of those overpaid Prima Donna's. I was however dismayed at the Welsh Players reaction at England's defeat, all very well showing a bit of pride in your country's achievement, of getting through to the next stage. Considering...
Hi,
I purchased a LAP non-contact voltage detector to check my sockets.
One of them is cracked and needs replacing. So I went to the Consumer unit and isolated the all of my circuits.
Then I went back to the broken socket and tested it again.
Everything appeared to be fine, and I removed...
berks1234
Thread
again
current
detector
live
prove
showing
situation
socket
tester
voltage
volts
Hello All,
I've been call to a small chapel as the power goes on and off once or twice a week.
Cable is a 50mm 4C fed from a 100A 6kA MCCB 50-60m away. 4pole RCD in Chapel.
Load on each phase is about 20-35A when the A/C kicks in so MCCB and cable OK for that.
IR at 500V Fluke 1653B. Results...
Hi guys
Have a problem with the tumble dryer that wasn't working and when the technician came out to check the socket with his device it showed up that the plug socket hasn't got an earth.
How would an electrician go about fixing the problem?
Thanks in advance
Nathan
NathanMorgan
Thread
earth
electrician
plug
problem
repair
showing
socket
without
I have a nominal 4Kw system comprised of 16 REY solar panels arranged on my roof with 11 facing south east and 5 facing south west.
it is now 11.15 am and the Gfi (Ground fault indicator) LED is still illuminated. The total generation (FIT) meter is showing a red light which means that no power...
silverpulser
Thread
facing
fault
gfi
inverter
message
power
showing
south
string
Hi Guys
Looking to see if anybody can shed a wee bit of light, got a phone call earlier tongiht from a customer stating he was getting a shock from the socket and the sink.
went over to have a look he advised he replaced all sockets with stainless steel ones and one kept shocking him so here...
Hi Folks,Any of you good people had any dealings with one of these systems? It's an old system in a large office type building. I know these are outdated now but been asked to have a look. Working fine until very recently. We have very little information on the system. Can't say sorry we're not...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc