I have a small mechanics shop in a rural area with no access to 3 phase. I picked up a air compressor cheap and knowing at a min. I will need a phase converter. I don't think a VFD or a static converter can do it. Is it even possible to run a 3 phase 30hp 230/460 90 amp Dual rotary screw air...
Hi,
Just someone setting up a mobile soundsystem for small pubs/clubs with a few questions about a distro. People IRL can't seem to answer my questions and the pro-sound light forums generally get too much conflicting information...
Hello all
Just doing some cable calcs for a shepards hut site, the site has an incoming supply of 2 x 250a single phase supplys, was hoping to run a 4 core down from incomer to a board then split off to each hut.
Do i have to work it out on single phase 230v or can i work it out on 400v
Hi, As a DIYer I`ve quite a bit of wiring up domestic house single phase experience but no 3 phase experience. So I have been offered a two post car lift which currently operates of off a 3 phase supply. I have a brand new single phase 3hp motor which I believe will run the lift but I assume I...
How should grounding be made to a 20kVA single phase generator set feeding a domestic property via a manual change over switch? At the generator's alternator neutral is bonded to earth. The generator will be some sixty feet from the mains input box of the property fed by SWA cable. The...
Been looking at what type RCD should be fitted for small single phase individual UPS.
Looked at Hager rcd selection guide under type B has 3 phase UPS but nothing for single phase .
https://hager.com/uk/support/regulations-18th-edition/selection-of-rcd-types
I am hoping type A will do ...
Hello,
I am hoping this is in the correct forum. To start, I acquired a film processing machine that runs on 3 phase. Now before getting the machine I fully understood it's power requirements and the cost of getting 3 phase installed at my house. I figured as processors are mostly a few...
We have two single phase heat pumps on two phases of a three phase supply the third phase has an immersion heater. The heat pumps are set up as master and slave with the master doing virtually all the work (22000kwh/an).
We also have a three phase 15Kw turbine. generating 45000kwh/an
Our...
In a 3 phase system the neutral carries current that is unbalanced. Okay.
So in a single phase domestic household the neutral carries the same current as the live otherwise the RCD will trip.
So does that mean if we have a perfectly balanced 3 phase system then if I go to one of the phases and...
Hi, this might be an easy question, but i need to power a single phase motor situated about 300 meters away from my MCC. Do I just run 3 phases 415VAC cable to the motor in the field and just connect one live phase and the neutral to get the 240VAC? if that's the case then what do I need to do...
Hi guys,
Been given a motor and associated control gear within a panel that has been water damaged.
This motor has 3 windings U1/U2, V1/V2 and Z1/Z2, 1 pair of wires for the brake and 1 for cut-out I believe.
In the process of wiring a new panel up for it and it know its a long shot but can...
hello!!
hope anybody can help me.
I have an AC single phase 220v 1.5HP motor that won't rotate when plugged in even when I try to do it by hand, it is kind of magnetically locked, and just hums.
when unplugged, it rotates easily.
I tested it with a new capacitor that I'm 100% sure is OK (I took...
evening all
ive got a single phase AC fan motor running normally however occasionally on start up it starts in reverse. i have 4 no fans, and this is happening to 2 occasionally. now these are in a fresh air chambers and i was starting to think that the airs blowing over the fans causing reverse...
Hi everyone
I came across a single phase 230v 2 speed pool pump motor the other ay and became obsessed with how they work and are internally connected , but cant seem to find a diagram/pic of the anywhere. I decided to do my own from what i found on line
My question is have i interpreted the...
Hi there, new to the forum and in final stages of completing C&G level 3; need to complete design project to complete. Am struggling to get my head around how to draw up correct circuit diagram showing EF Loop path for EV charger where initial supply is described as 'three phase TNCS' feeding to...
Hi all, new to this thread and just looking for some views.
I have today attended a industrial unit which is being converted into small individual offices. An electrician has previously been here and has taken 3 individual sub mains from the existing three phase consumer unit to single consumer...
My 3 phase cnc lathe is rated at 27 Amps on the manufacturers website.
When I mentioned that I want to run from a single phase via a rotary inverter I was told that it will need 27 A per phase therefore 3x27=81 Amps from my single phase. Is this correct? I reckon the machine is about 5hp.
Hi,
We are being asked to make a power supply for a Bass amplifier......its 4kW, from 100-265VAC.
Does that sound right?
Woudlnt 4kW from 115VAC always be done with three phase?
(this kit is for mulitple different countries)
Hi, morning EF.
I was looking at a single phase motor yesterday attached to hydraulic pump for cardboard bailing machine that seems to be temerpemental with stop and starting and making humming sound.
I checked the contactor was working first and voltage was going to motor, I clamped the cable...
Weired one. Looking for info or past experiences. Called to a garage very old ramp 40+ yrs old not working. Very old switcc looks like its burnt out, so before i take on finding a replacement i wanted to make sure motor ok. So bypassed up down switch and turned on isolator. (Single phase motor)...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc