someone | Page 3

someone

Recent contents View information Top users
  1. T

    UK Finishing someone else’s work

    Hi all new to the forum go easy, I’ve been asked to finish a job off (going to look at it tomorrow to see how visible the install is) just wondering how we go about this? Obviously i will test before anything would be done but what to do after just issue a PIC and tell the customer to notify...
  2. P

    I Need Work Looking for someone to give me work experience or sponsor for an apprenticeship?

    Hi I am located in Blackburn lancashire. I am currently studying level 2 diploma in electrical installation. I have been told I need to either do a week work experience with and electrician or company to pass my course. or have a sponsor for an apprenticeship. if anyone can help me it...
  3. Mark Wright

    I Need Work Best way to find further work experience with someone trustworthy I.e not a cowboy

    Can anyone give advice on finding work experience with someone who's not a cowboy, I'd love to continue this line of work it's been quite a ride but like many finding work experience is hard, i'd love to find someone who follows the rules etc and not smoke breaks every 5mins. I did contact one...
  4. J

    Camélia a Mechanical calculation software download link

    Hello, I would like to download Camélia a Mechanical calculation software for overhead distribution lines. can someone have it's installation or link ??
  5. D

    I was wondering if someone has five minutes to review requirements?

    Good Day; I am installing an external portable 4KW, 30A generator to my small mountain cabin. I have accounted for an external generator hook point, external 30A fused disconnect leading to the internal 12-way Square-D power distribution board. An external 4ft copper ground rod provides the...
  6. M

    Removing Old Cable TV Wires From House Exterior:

    I have what I think is old cable TV wires on the exterior of my house. I am hoping that someone from this forum can confirm from these photos that that is what I am looking at. I know for sure that they are not my Verizon Fios wires. Thank you in advance :)
  7. C

    Fast track electrician qualification for someone with a Masters in electronic & electrical engineering and 12 years experience

    I hope everyone is well. I know fast track courses are frowned upon but it would be great to have people's constructive thoughts/recommendations on a fast track electricians course for someone who has a masters in Electronic and electrical engineering and 12 years electronic design experience...
  8. S

    Can someone please tell me what sort of unit this image is.

    Can one of you kind electricians explain to me what the unit in the image is and the function of the two buttons please.
  9. J

    Double to single light switch

    Good morning all. I am new to the forum and hoping someone can help with a query i have. Currently i have a double light switch which operates two separate lights at each end of my kitchen. I would like to change the light switch to a single allowing me to turn on/off both lights at the same...
  10. A

    Has someone some exploded views of the N20, N40 and N80 rotary cam switches from Telux (Benedict & Jäger)? Where could I found them?

    Greetings! I'm looking some exploded views of the N20, N40 and N80 rotary cam switches from Telux (Benedict & Jäger). Some of my customers tried to repair their switches and there are some parts missing, so I'm looking for part numbers and their exploded view. If you can share the information or...
  11. S

    Bit of advice for someone looking for a career change.

    Hi all just joined because at 37 I'm after a career change. Been thinking about sparks for a while, and more recently feeling the need for a more stable career. I want to do it the right way, and get the right certs. I've been looking at the tradeskills4u course, which savings and a generous...
  12. D

    Hi there, and am hoping someone can help

    Hi there. This is my first post ever on here so please point me in the right direction I am looking at some advice on 6mm squared armoured cable? Source URL: The Welcome Forum - https://www.electriciansforums.net/forums/the-welcome-forum.19/
  13. B

    Can someone advise what’s going on here please

    Hello, I am tiling our kitchen and needed to replace some plasterboard near 2 double sockets. The builders were a little enthusiastic with the plaster adhesive, resulting in a large bulge and wonky sockets ?. Anyway, lots of hacking later and I found the setup on the photo. I was expecting one...
  14. J

    Can someone please tell me how I can bypass this ?

    Is it possible to bypass this ? I know it is a bit rough looking. I think it was a latching 3 dpdt switch that was there. ( push in - on) I want to no how I can bypass this or make it always on. Any ideas on how I can make it work would help. Also please note * I do not need power to come...
  15. C

    LED Lighting

    Hi,Im just a fresher as design engineer. While browsing, I read that 330ohms resistor has to be placed parallel across an LED light, can someone tell me if it is necessary and why?
  16. B

    UK Seeking some advice from qualified electricians or someone in the know

    My partners ex husband installed a trunking strip in the office of the house. There are x4 double sockets x1 single socket and multiple data connections. This is all ran off 1 outlet from and existing double socket. The plug is rated at 10A. Just curious what legal requirements are for this. She...
  17. P

    Help, I’m sure someone can answer this very quickly

    Sorry, I’m new to this. Can someone just explain how I should wire these cables in the ceiling light unit as per images, there seems to be a lot of cables,
  18. J

    Can someone help me fix an issue with my doorbell?

    Ok so I tried to replace my door bell, but when I took it out the wires were twisted and snapped off too short to rewire. I’m a trainee electrician with little to no experience so I’m stuck. Can I get some more wire and try to extend it by wrapping it around the old wire and covering it with...
  19. J

    UK Can someone help me wire a new light fitting into an old house with old wiring systems.

    I’m a junior electrician, fresh out of college. I did some minor electrical work for a friend buI tried to put up a new chandelier I came across: Two Line wires (RED), going into one connector block Two Neutrals (BLACK), separated into different connector blocks - Two CPC wires, going into...
  20. R

    Is someone trying to rip a customer off? Advice on a Fire Risk Assessment

    Hi So a customer of mine has just had his fire extinguishers tested and for some reason the guy doing the fire extinguisher check removed this 600x600 flat LED panel and looked above it and said that what he sees is not safe and it's a fire risk. He proceeded to quote £600 to have 7 of these...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top