spd | Page 5

spd

Recent contents View information Top users
  1. C

    SPD requirements under 18th edition.

    Hi all, I haven't done domestics for a while and have been asked to install an 18th edition CCU to a small terraced house ( 2 floors Ground and first). I been told that I need to install a SPD? Can someone confirm this is the case and are there any exceptions. Haven't done my 18th but will be...
  2. E

    Introduction to Surge Protection Devices

    Hi Guys just reading this link & thought someone might be interested Practical tips for installing surge protection devices in low voltage panel | EEP -...
  3. PJH2903

    Stroma Certification Scheme SPD calculation / Stroma annual assessment

    I've got my annual Stroma assessment next week and the job I am taking them to is a board change. I have not fitted an SPD as by my calculations it was not a requirement (plus a tight customer would not want the extra cost) I don't think it will be a problem but am just looking for reassurance...
  4. C

    SPD Board xxxxxxxxxxxx

    Somebody asked about a month ago if i had a picture of the SPD Board Hager do. Cannot seem to find the thread, anyway i have just done my first one since. Pictures attached. Quality make of board, really solid. I know its not the neatest, i do one cable at a time instead of all CPCs, then Ns...
  5. mattg4321

    Rewiring a 2 bed house to be rented out - SPD required?

    As per the title, if you were rewiring a small house to be rented out would you, or should you fit an SPD? Doing one soon and been screwed down on price a bit further than we would like ideally. However we have a quiet few weeks until a couple of bigger jobs start and it's local and empty...
  6. Simon-0116

    spd on 3ph distribution board

    Priced a job to change old 3ph board from pictures alone. No the firm so jobs good. Get there and situation is no spd fitted on existing. So I was going to fit one to my new db in trunking at side of board fed of 32a breaker. Will this act / cover / work for the whole site. Layout is main...
  7. M

    Advice needed On 18th edition boards. When do fit SPD boards?

    I’m An NICEIC DI. I haven’t got around to doing my 18th yet and I haven’t got the new literature. How do you determine if you need to fit an SPD board. Should I start fitting these on all my jobs now?
  8. B

    SPD requirements for additions and alterations.

    Hi Apologies if this has been covered. With the extension of the requirements for Surge Protection, I am unsure as to whether this is only for new installations and DB changes, or if the regulation also applies to alterations or additions in the same way as RCD protection. My thinking on...
  9. R

    New consumer unit on TT installation - earthing and SPD queries

    I'm going to replace the consumer unit for a customer in rural Oxfordshire. The supply comes in overhead, drops down a telegraph-type pole into the ground, and runs about 2m to a recessed box in the wall (perhaps coming up in the cavity). I can't find the earth rod - probably entirely...
  10. C

    SPD to cover whole site?

    Hi Guys, Having recently done my 18th, and various reading of SPD requirements, I feel that within the factory where I work (food industry), we should be using SPD's? We have an onsite transformer which we own, 11kV to 400v, which then splits after the meter to two main switch panels, which...
  11. I

    Another SPD question & groupin query

    In a domestic situation where dwelling would be used for air b & b would it still be classed as single dwelling? Would it be classed a comericial dwelling as people staying there and paying , also would there be requirement for surge protection , I Would assume so , as items in property value...
  12. C

    SPD risk assessment template

    I am due to carry out my first fuse board change under the 18th edition, i need a risk assessment template for SPD devices. and with regards to AFDD i am under the impression i just need to recommend it in the quotation.
  13. N

    SPD For Large Panels

    Has anyone got any knowledge of a decent SPD that I can retrofit onto large panels? Preferably I would like it to have its own enclosure and a set of VF contacts so that I can wire an audible alarm and light to them for ease of checking. I am struggling to find anything suitable. The USA...
  14. spud1

    Why are the two poles of the Hager SPD rated differently

    So I was installing a new split load Hager DB (with the integral SPD) and noticed that the SPD cartridges connected across the neutral and line poles of the SPD were rated differently. Is there a reason for these different ratings? Spud
  15. J

    SPD for dis board change in warehouse

    With upgrading a TPN dis board in a warehouse- i am guessing I need to fit a 4pole SPD even more so with 18th edition out I will be installing a hager 12way TPN board with a 4pole incomer kit. Technical Properties SPN415D -...
  16. bigspark17

    Spd & 18th..............,,,,,,

    So am i correct than reg 443.4 means unless we provide a risk assesment that states why we are not using a spd in consumer unit changes then we must fit one??
  17. 1Justin

    Best value fused switch plus 2 module type 2 SPD?

    Has anyone done this yet on a budget? I'm pricing a job to run a submain off a TN-S. I'll need a fused switch incorporating SPD alongside in the same enclosure. Price sensitive. Thinking of a budget Lewden off the shelf fused switch (in 4 module enclosure), ditching the enclosure and buying 6...
  18. mattg4321

    Surge protection devices (SPD)

    Hi guys, hopefully someones going to be able to point me in the right direction here. We do a lot of work for a small retirement home locally that has recently decided to fit lightning protection. We've pretty much been strong armed into fitting SPD's on behalf of the lightning firm (LF). Being...
  19. R

    Wylex Fuseboard SPD.

    I am about to install a new high integrity wylex fuseboard within a church which will require a combined type 1 & 2 SPD as the church has a lightning conductor system in place. Can anybody confirm the connections to this as it is placed within the fuseboard upstream of the main switch.
  20. B

    SPD in large switchgear

    I was assembling a large distribution unit today. Hager type with a 500A main switch. There are 10 x 100A MCCBs going to be installed The board, MCCBs etc came in a kit, which also had a surge protection device with it. The client did specify the nee for the SPD however the SPD itself has...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top