steel conduit | Page 2

steel conduit

Recent contents View information Top users
  1. E

    Testing steel conduit

    First time i have worked with steel conduit as a cpc and wondering how to get a decent R2 test. The back boxes are showing signs of corrosion and so is the conduit where it is exposed so would like to test to see if i'll need to add a cpc to the circuits. I have a kewtech 65dl tester and...
  2. H

    steel conduit help

    hi everyone i've recently started using steel conduit and so far most of the jobs where i've used it have been fairly simple (straight runs). i've got a job that requires quite a few 90 bends to be made (i've bought a hilmor bender and have been practising using it) i've just got a few...
  3. H

    Steel Conduit

    Hi Just got a quick question. I install CCTV systems and want to start using steel conduit instead of PVC. Do I need to ground the conduit if it will only have CAT6 network cable inside. Thanks
  4. Pete999

    Steel Conduit

    I was wondering last night, or should I say wandering, when I were a Lad working with steel and Galv conduit, I distinctly recall the Electricians I was working with always gad me filing the ends of couplers, locknuts etc and also removing the pain from entries into steel enclosures, I know in...
  5. A

    PVC to steel conduit adaptor

    Hi, I was just wondering what the best way to connect PVC to steel conduit is? I was thinking PVC male adaptor and a steel conduit coupler? Cheeeeeeeeeeers :D
  6. B

    Steel conduit

    How's this for a means of earthing this steel conduit is acting as a tt arrangement, although brilliant ze readings, 6.41 ohms 34a. What do you all think to this.
  7. Corbs

    Steel conduit

    quick question does steel conduit need bonding at the start and finish of the run, because i have a job coming off soon replacing some metal twin fan extract units to plastic inline fans, at the moment the conduit it attached to the fan and the fan is earthed via a separate cpc in the conduit...
  8. Tuttle

    RFC in Steel Conduit

    I plan to install steel conduit (used as cpc) in a garage / workshop. I intend to run the conduit in a complete loop around the garage, i.e. starting at one point, going around all four walls and then back to the point at which I started. I want to do this because it makes wiring easier, i.e...
  9. M

    Steel conduit

    Did the 2394 written exam found it fairly simple enough. I hope haha got a question come up about steel conduit it said a steel conduit system needs to be check before any cable is installed name five checks you would carry out and what you are doing by doing each check? just wanna see if...
  10. D

    Testing RFC in earthed steel conduit...

    Excuse my ignorance on this, never had to test a RFC when the conduit was being used as the CPC. Obviously can't do the usual test for continuity so can't tick that box on the form, will just note that it's an earthed conduit set up. Where I get more confused is the R1+R2 measurement seeing as...
  11. Marvo

    Steel conduit wall thickness

    I'm hoping a few of the older members might remember this. I need to know what the standard wall thickness used to be for the very old type threaded steel conduit (20 and 25mm equivalents). I'm guessing the diameter and wall thickness was in imperial sizes so I also need to know what the...
  12. S

    price per point - steel conduit

    Not done this for a while. What's the going rate per point. standard metal clad sockets, spurs and switches. Light fittings budget fluorescent. Runs aren't long. We are sub for main contractor in SE. Any help appreciated. Thanks
  13. S

    Arrrghhhh! I have a practical assessment and im struggling with steel conduit?

    i have a practical assessmet coming up and the problem im struggling with is the steel conduit. Well its a double set out of the C.U and its roughly 15-20 mm from back of conduit to the wall. im not using an angled ruler, the main problem i have is where do i put my second mark on the conduit in...
  14. J

    2 way lighting fault - in steel conduit

    I was looking at someone's hall lighting the other day as neither of the fittings work. It's 2 way with 2 fittings in an apartment all wired in singles in steel conduit. There's power to & leaving switch A but no power at either fitting or switch B so there must be a cable break somewhere, only...
  15. S

    tips on bending awkard angles on steel conduit.

    I have to bend some steel conduit as shown in the picture about how would you get the angles spot on? The picture isnt really accurate as i belive the 2 sets will be similar. doing it another way isnt an option as thats how the client wants it too look like. the black opject is a wall support...
  16. P

    pvc or steel conduit?

    Hi everyone. May have a job coming up in a school where there may be a floor socket needed. The socket is about a metre away from the wall. Not sure if to use pvc or steel as it will be screeded after. Its at a depth of 100 mil. Thanks,
  17. C

    T+E in 25mm steel conduit?

    Hi every one, Im new to this forum. FNG!. A simple question that I cant seem to find the answer to is can I run TnE in steel conduit? I know singles would be the best option but the customer has lots of TnE and wants to keep the cost down. I would strip out the cable but I dont have enough...
  18. S

    steel conduit

    Would you put this as a code 4 on a pir? No steel conduit boxes have earth fly leads. By my understanding they all needs to be eartherd.
  19. B

    help with steel conduit and trunking

    hi chaps after serving my time doing small elec repairs and installs,i then worked in the service field for approx 20 years.I am as good as anyone fault finding on any circuit or control circuit etc.However i have a strong possibility of a job offer ( i know thats very rare in this current...
  20. DaveyD

    Cooker Switch to Cooker Connection : Out of zones. Earthed Steel conduit or trunking?

    Evening Gents and Ladies So, moving a cooker switch that's over a hob 300mm to right. Want the Load cable below surface to drop down to below work surface within zone BUT then end up back behind fitted cooker not the cabinet below. As subject, what do you guys do? Would you do as I do for eg...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top