Hi all, we have a situation where we have a 3 phase bit of equipment thats on a 32amp commando plug 3 phase. Its wired up in sy cable and using an sy gland the braiding is earthed on the load side. There is no room in the plug (supply side) to get both the braiding pigtailed up and the conductor...
Hi guys,
I have my am2 resit this week, I just done the pre assessment day and I was told that the sy cable needs to have a lock nut either side of the gland. So two lock nuts on each side.
So one to lock down the two washers and then one to lock them together in the box...in the videos...
Morning all
So the site I'm based at recently had some work done (think partitioners). This package of work included electrical. This was actually good news to me in a way, as it was one less job for me to do on an already busy schedule - but it was niggling at me that I'd possibly end up...
Hi All
got a question regarding SY cable. I have tried to find the current rating for 6mm SY cable and have found a data sheet the GEM cables which states 33 amps in conduit thermal wall and 54amps when in free air. Also seen a few other manufactures state these ratings but a lot stating...
I recently bought a catering trailer and have been advised I need to have it re wired using SY cable.
I can't find much information about this and want to make sure I am going to be getting the right thing done.
Thank you for any replies ?
Hi, got a job that’s coming up which involves putting electricity to a wagon that’s half way down a field from someone’s house. They want it so it’s like a caravan, so they can disconnect the power lead whenever they want and move the wagon around.
There’s only 2 circuits in the wagon; 4 lights...
Peeps,
Your thoughts please on the use of sy cable in a domestic setting.
Came across an installation today where the supply to an immersion element had been run in sy cable. Overcurrent protection correct and circuit is covered by a 30mA rcd.
I think we are going to be doing an EICR in the...
k guys needs some advice,
We have an event on tomorrow and we been asked to run 100m of 4mm sy cable to power up the event.
Now I know have mixed options but can this be done or should it be run in SWA cable??
The cable will be protected by 32amp in a splitter box
Cheers guys
Morning all
I've recently been introduced to SY cable through work. I've had a look for more information on the web as I wanted to check ratings, uses etc. but I'm getting a lot of mixed information... many people say they use it but many others are saying that it doesn't comply with BS7671...
Hi all,
Just a question relating to SY cable and the use of SY cable. My boss his carrying out a EICR for a industrial premise and coming across a lot of SY cable. These cables are used for final circuits and distribution circuits. I know that BS7671 list SY cable as non - standard cables and...
Has anyone used SY cable to send data down? Thinking about potentially running an intercom from gate at top of driveway down to house via SY. Thoughts?
Hi guys new to the forum and will introduce myself shortly :p
I have attached an image of a spur i have taken as you can see from the attached image
I am doing a trainee maintenance engineer role and just wanted some info on the below.
1.) when using sy cable do you have to earth the sheeth...
Hi,
ive just done the prep day for my AM2 and they are using a gland to terminate the SY braided cable that I haven't used before. I have been practicing using the one that is on you tube etc where you twist the braids like a moustache etc. The one they insist on using is the same as an swa...
I've got a new installation within a biomass boiler building connected to an installation I've just carried out.
The boiler room install has been carried out by a non registered contractor and as it's been connected to my install, I've been asked to carry out an EICR by the client.
The...
Hello,
Im half way through my am2 with just the heating and sy motor to do tomorrow,
but I am just wondering about the braided cable.
do I just have 2 pigtails of braid sheathed up with earth sleeving connected to earth in both the starter and the motor?
Any help is appreciated
Thanks
Can anyone explain clearly how to gland this off? Or have any videos? SY cable is involved in my upcoming AM2 but Ive never done it before. Suprisingly cant find anything on youtube! :(
Any help greatly appreciated
Hi,
New to the forum so hi to all, have a question regarding the above.
Have a control panel going to the USA and wondered if SY cable is OK to feed some motor mounted inverters that are mounted on pump units which are installed in adjacent cubicles to the electrical cubicles. Cables do not exit...
Bit of advice required guys.
i have to do some refurb work on a listed building where previous works have been required to be in MICC
this works will require a completion cert when finished.
However, recently an approved contractor has carried out work on part of the installation where a...
Hi there good evening chaps.
just wondering if anyone could help me out with some info on terminating SY cable using the proper glands. I have my am2 next week and although I have done the pre am2 and watched the video on YouTube I'm still a little confused. Because on the video the guy says to...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc