Hi,
I have just bought a number of electrical switches for my hall way. All seem straightforward to change over apart from one. It is a single switch in a hallway there are two other switches that control the same lights but their wiring seems straightforward. The switch I want to replace has 4...
hi guys, customer has no thermostat for his heating so he brought a Honeywell dt92e. I am trying to install it but can't link it up with the programmer (2 channel Drayton) I have wired the stat up with a perminant live and it fires the boiler. But I can't get it to work properly with a...
Just acquired a Reliant Scimitar...SE6b ....fibreglass body so earths are all over the place. .. waiting for carb to get it running but meantie the seller says it fries alternators. There's a three way connector on the back of the alternator and a spade terminal unused marked B+ ..I thought...
Hi, DIY'er here. Looking for some expert help as I am very confused :-) One of the sockets in my living room doesnt seem to be working after I changed the socket. However when I use my voltage tester it tells me the current is live. I have checked all the connections in the socket and they seem...
I have just had a professional firm redo my ceiling under an insurance claim and this is how they refitted the light (I removed the covers to reveal the terminal)
I don't know much about building regs and electrical compliance. Can someone tell me if this is OK? My instinct says no F*ing way can...
Hi I hope someone can help with this. I cannot contact Honeywell to help by phone (lines constantly busy) I emailed them on Monday and still heard nothing.
I replaced a Honeywell smartfit wired controller and programmer with a Sundial Y9420S RF pack3 wireless system.
I have found that the...
When wiring an rcbo where do you tend to put the functional earth? I'm assuming it will be tricky to ensure the small functional earth will get a good grip when placed with its corresponding cpc, so do you put your functional earth in its own terminal?
i am trying to install a 1no1nc push on off led switch in my car to intercept my power antennae. it has 5 terminals with red, white, black and 2 green wires. the 2 green wires are marked NO and NC. i think the red is marked+. cannot see any markings for black and white wires.it did not come...
I am about to connect up my 12V battery to my inverter (at last!) and I need to crimp some copper tube terminals on to the end of the cable. I have purchased an indent crimper for these tube terminals but I notice it is different to my crimping tool for insulated crimps. The stem of tube...
Hi, I am trying to find a place where to buy "square headed" bolts for battery terminals?
Like the one on this battery terminal:
http://www.pcscables.co.uk/images/1802/main.jpg
Obviously, if I buy new terminals I will get these bolts on them. But I would like to buy the bolts only, and...
Evening All. I am about to carry out a domestic rewire to a property which has TNS earthing. The DNO has recently done a bit of work installing a new isolator, smart meter, contractor for Econ 7 switching etc and tidied up their end of things a bit. There is no MET at present and everything...
Hello I'm new to the forum and this is my first request for some help and advice please.
I have a present a manual Honeywell room thermostat..
i am wanting to change this for a RF thermostat and reciever as I'm disabled and will save me having to go into another room to turn on the heating as...
Anyone know where I can get either a class II door switch or one with somewhere to terminate the CPC? The Jeani ones I've seen are not class II and do not have an earth terminal.
Hey everyone. Bit of a silly noob question.
On my dirt bike, as I was tightening the positive battery terminal lead(it was loose), the allen key slipped and hit against the subframe causing a short and sparks everywhere, and causing the allen key to be extremely hot to touch.
It was only for a...
I have the above 3.0 kVA generator to power a caravan and I am unsure about the earthing requirements. After reading the manual and the HSE guidance I am of the opinion that it is a floating earth and an external earth rod is not necessary. If anyone knows any different or has any advice, it...
Does anyone understand main AC terminal markings of N G F (left to right)? Is that Neutral / Ground / Line as it is Italian supplier and possibly far east maker. I have not come across this before so just checking before I wire it in.
It is PCB mounted terminal block so i cannot see any other...
Hi
I've installed the electrics for an underfloor heating system. The system has 6 manifolds each with a small pump. There is then a primary pump that pushes hot water through the system from an aerobic digester next door. I have fitted 6 contactor each using a switch wire from the thermostat...
Hi Folks
As per my previous thread. I plan on making and selling some lamps. I want to have two versions; one with a metal bulb holder and another, cheaper version with a plastic bulb holder.
The issue is that I am using 3 core fabric cable and the plastic bulb holder does not have an earth...
Morning,
I’ve only ever used a kewtech MFT and I’ve bought a Megger 1710
On the back of the tester above I have the following colour coded terminals for the test leads.
L3 Blue
L2- Green
L1+ Red
Q1. What leads should I plug in to do the end to end tests on a ring final circuit.
Doing...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc