Hi,
Got a customer who currently has an Enterview 3 system, 1 mag lock, 1 external unit and 4 handsets over 4 floors.
They want to upgrade to something more modern, this isn't my main area of expertise so looking for some ideas.
Most new systems seem to be network enabled, so poss could ditch...
Have a quote from UKPN - £10K (with us doing the trench and duct work on our property). Actually could be worse I know, but as the substation is literally across the road it is still quite pricey.
UKPN refers to ICPs who can also do the work.
Is it worth worth trying any of these, in which case...
I have a wireless texecom panel with v3.02 firmware, and I want to add a texecom ethernet connect unit but the panel has to be upgraded to version 4. I got the unit below in the connect box, so can this upgrade my panel to version 4 or do I need to buy an actual flasher unit (about £38 from...
Hi Folks,
Not been on here for a while, but something came up the other day that has me concerned to the point I thought I would ask here.
A good friend asked me if I would connect up a new electric shower for him. This is an older gent, a farmer, and as much I like to look out for him and his...
Hi all,
I have some outdoor lights, and I want to update the circuit to add a bit more functionality. I have drawn a little picture of what I have now:
When we walk past the Outdoor PIR sensor 1, all lights come on, and then go off. This works fine!
Now the behaviour I want:
Add another...
Hi
We've just moved in to a new house and it's got 3 outdoor security lights in the back garden. I've tried to trace the wiring back inside but I cannot find where it goes other than finding the ring that it's on. The plug (if there is one) could very well could be hidden under the attic...
Looking to upgrade the current consumer unit, it is located in the garage, the new cu will be in the same location. Having read various posts it appears that the Hager boards are well regarded but the MK boards not so
But my electrician is adamant in wanting to install an MK RCD board 13 way...
I have been meeting with solar system installers to install a grid-tied system at my house. Before I commit I want to verify whether I need to upgrade my main service panel.
I have been reading about the 120% rule and am not sure if my current main service panel is sufficient. Any assistance...
Good morning
does anyone know about anything in the 18th edition and the requirement to upgrade consumer units when electric hobs are replaced?
i had a customer ask me about it this morning.
Many thanks
Simon
Hi
As part of a loft conversion to my 2 (now 3) floor flat in a Victorian Terraced house I have added about a dozen 2-gang sockets, a shaving socket, and about 16 downlights to my new floor, plus swapping four pendant lights for 16 downlights in the floor below.
An electrician was installing a...
Hi all,
Looking some electrical advise. I've been told by an electrician that I need to install 5 Nr RCBO's to this consumer unit. Is this correct or is the current set up ok? He has provided me with a condition report stating a 'C2' on the cables concealed in walls. If an upgrade is required...
UKPN came out for a client as I suggested they have their supply upgraded to 100a.
My new tails are 25mm from the consumer side of the service double pole isolators.
What I can’t understand is that UKPN won’t upgrade the head because the tails which I cannot touch (between the bottom service...
On an eicr we can write LIM for L-N testing and do a test with L-N connected to earth if there's too many electronics to unplug.
What about on an EIC when only doing something like a CU upgrade? Can't do the IR test between L-N with too many things to unplug and we can't write LIM on EIC in...
Ok, I’m a relatively new domestic installer and would value the opinions from you more experienced guys.
Went to look at a job which was outside lighting, gate lights, drive lights, security etc and changing some fluorescents for down lighters in an outbuilding... straightforward. When I went...
Hello all,
I am about to receive planning permission for 6 one bed flats conversion from an existing family home. The current single phase 100A supply will not be sufficient so I have applied for a 3-phase upgrade.
My question is on maximum electrical load per flat.
I have done a similar...
Just want to pick your brains.
When your completing the EIC on a consumer unit upgrade,what do you guys put on these parts of the schedule of inspections.
Section 8.3, 8.7.
My accessor said I should put “LIM”, but you can’t put “LIM” on a EIC! Obviously for section 8.7 you can’t possibly...
Hi, everyone.
I have a shower room that currently has hot water provided by a 7kw tankless water heater. The room is plumbed for hot and cold water from the domestic hot water (oil fired), but the pipe is so long (more than 60m) that it's barely warm by the time it gets there, hence the heater...
Has anyone installed the new compact rcbo from crabtree and noticed a flaw that they have introduced that doesn't exist on the older larger model starbreaker rcbo..
The basics of it are that the new compact rcbo when plugged into the busbar in a circumstance that many will come across where you...
Just for your information, to conserve energy consumption with your underfloor heating, it is a great idea to replace your old thermostats with the programmable thermostats. With this kind of thermostat you would be able to set the timer to go on and off at certain times of the day. With this...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc