Hey there, new to this forum and hoping I post this in the correct spot.
Ive been doing some new lighting hookups in the basement, and after I finally finish it all, I decided I want a new fancy lightswitch. Unfortuanly I cant do a smart setup because most require a neutral wire (house is a bit...
Hello,
We just changed the lighting of our kitchen. It was a ceiling light with two rows of spotlight. The new lighting only has one row. When we removed the old one it looked like there was too many wires - two big cables with 3-4 wires each.
There’s 2x red (L), 1x blue, 1x black, 1x yellow...
Hi guys
Have some trouble here.
So I'm doing terminations at work and using side cutters, usually on 1.5mm or 2.5mm. Seems to happen more with stranded.
I'm squeezing the cutters a bit and turning the side cutters around the wire and often the insulation bags up against the side cutters and...
I have a fair amount of basic electrical experience but have never dealt with 3 way switches. I am upgrading the 1970's wiring in my attic and came across a light fixture controlled by a 3 way switch. If the 3 way switch is in the off position, the switch on the other end does not function. The...
Hello,
I have a generator that generates 14V/20A DC for two ends and I use both of them for operating olive harvesting machine.
I have no Idea how much wattage or Amp each one needs because it came off the label , but I know that they both need 12Volts each.
The issue : operating both on...
I am doing a 100 to 200amps (underground) service upgrade.
Can I use the existing 11/4” pvc pipe to run the 200amps rated wires?
What is the smallest size of wire I can use for the 200amps?
Is (2) #2/0awg copper & (1) #6awg neutral copper ok?
So I was installing something and accidentally cut the alarm wire going to the door sensor. It was two braided wires. Please see pics below. Any help would be greatly appreciated
Hello all! Probably a noob question, but really appreciate your help with this. I am trying to fit a ceiling light and need to get out the existing electrical fitting to be able to screw in the base plate of the ceiling light I bought. Below are the pictures of the existing electrical fitting...
Putting in a new garage sub panel, but none of the wires pulled to the garage were marked. There are three #8 wires, 2 hot and a neutral. The hots are on a 2 pole breaker. If I turn the breaker on and test for voltage, the neutral should not be hot. My question is, can I remove one of the...
So, this is my situation, and I'm just wondering what a real electrician would do. I don't have any money right now and can't call anyone, so I'm just living without hot water and using the RV campground's bath house.
My propane water heater broke, and I didn't like using propane anyway, so I...
Hi all, I’ve removed the antiquated burglar alarm from the wall in my understates toilet. It’s on the circuit marked as ‘downstairs lights’.
I had expected to be able to simply joint the corresponding wires that went in and out, but they’re not the same colours!
Any advice on how I should...
Hi all,
I'm wiring one of those smart switches which is a single gang and I have three live wires (x2 com) (x1 L1) and three neutral wires that are currently in a block. The original switch just use live (com and L1).
I've wired up the new switch with the live wires but I am trying to attach...
Hi
I am trying to wire, what I thought was a simple, light switch. The problem is there are a lot of wires from the previous fitting going into a new one.
Can someone help me to sort out wiring for the new switch. I have attached two images one for the old wiring and one for the new one.
Can anyone tell me whether these wires are suitable for a non experienced individual to be near or exposed too if they have no knowledge. We were told by our landlord to access the thermostat shown but the wires surrounding it are live and need insulating (nothing about insulating wires was...
Hi folks, I'm in the process of adding some more sockets into my "Socket" ring circuit. My plan was to open up the existing socket, cut 1 twin and earth higher up and add a socket there, leave the other twin and earth where it is then do a small ring of 4 sockets, starting at the existing socket...
We have got a chandelier but the wires are clear it has 2 clear wires and a earth wire but one of the wires has a S on it what colour does this go to on the ceiling rose thank you for reading
hi there
Looking for advice. I have string lights in my kitchen and twice now, where the wires connect to the transformer they melt! I have the transformer connected to the mains which comes from the wall switch. Any idea why the wires are melting?
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc