Afternoon,
I am about to install a solar panel on my shed and wondered if someone could explain where the inverter should be connected from?
Most diagrams show the inverter connected to the battery (pic1), but some show it connected to the load terminals in the charge regulator (pic2). I am...
Hi
We are looking to replace an existing roller shutter door motor with the below Garog motor and wondered if anyone had a wiring diagram for this?
Make: Garog
Type: ULA25EE
V 400
A 1.0
KW 0.5
RPM 28
PH 3
HZ 50
IP 44
Hi all.
I'm looking to incorporate a switch to an existing pir floodlight, to have the option of motion sensor or permanently on - could anyone point me to a wiring diagram for this?
Ta.
Hello,
I am in need of a wiring diagram for a Tecalemit two post car lift. As for the model I don't know because all it says is tecalemit and Siebe.
The control unit has a ON/OFF Isolator and UP/DOWN switch on the side. I basically need to know how to wire the mains supply into it. two limit...
Hi all, would you be able to confirm the attached diagram will do the described scenarios?
Original diagram
https://www.dropbox.com/s/fp4td333alpe335/800px-MultiPIRandLampCircuit%20Original.gif?dl=0
Amended
https://www.dropbox.com/s/vkbpfwp7atlc9vs/800px-MultiPIRandLampCircuit.gif?dl=0
I'm...
Hi Guys
I currently have a combi boiler with a single prog stat wired direct to the boiler. I am putting in UFH in my kicthen diner and have to zone off using an S Plan Plus config. I have a Worcester Bosch boiler. I have drawn up the attached wiring diagram, would anyone be able to verify...
Hi guys long time been here ok im helping to build a drift nissan 300zx and the owner has asked me to only put in the bare minimum when it comes to electrical so literally fuel, ignition, crank headlights, taillights, indicators and wipers thats it as all the luxery accesseries are thrown away...
Afternoon all
Does any body have a wiring diagram for the installation of CT'S into a ryfield ct chamber.
I have installed the chamber and the eon meter installer had said it is my responsibility to wire the CT'S and do all the interconnecting cabling to allow him to fit a meter. I have had a...
Hi all,
I am trying to install the above sounders in a new alarm system....
The panel that I am using is a honeywell accenta G4 panel with the above
sounders, however the engeers manual does not give me the correct terminals
for these bell boxes?
Can anyone help me with this...
Allreet, Does anyone have the above or let me know how it needs wired? Its the usual social housing rubbish thats normally issued.
Terminals on programmer at are the usual - N - L - 1 - 2 - 3 - 4
Terminals on the stat are the usualy L&N - L1, LX, L2
cHEERS
I have a loft conversion to wire next week, and the local building control have asked for a wiring diagram before starting work. The work is just a few sockets and lights.
Is this a common request - this is the first time I've come across having to provide this in advance? The customer is...
Hi everyone.
Any help would be very appreciated.
In the process of building/wiring an industrial oven, im planning on purchasing all the components in the morning so i would really appreciate it if you could have a look at my wiring diagram. I am studying Electronic Engineering at the moment but...
when i was ready to install entry door system i see on the kit box its not any instruction book and wiring diagram..the entry phone system its TARGHA BPT with 3 individual telephone..its any one who have wiring diagrams for them..
Hi,
I want to wire up a 12V DC timer (CN101A) to turn an appliance on and off. I have the found on the internet the following wiring diagram for the timer and not being too experienced I was wondering whether it will work if I make the connections as shown:
The timer does not show + or - so I...
I've been asked to wire a heating system which I havent done before. Plumber a bit vague in how its all supposed to work. Don't even think he knows!!
It incorporates a dunsley baker log burner stove and condensing system boiler. It's a gravity fed hot water tank with a neutralizer...
A customer has an existing application using 2 off, 4 pole contactor/relays of Brook Crompton make, model HR1310 and 3 capacitors of 200, 60 and 20 microfarads. The 3 phase motor is an English Electric, 4 pole with nameplate details - 2 HP, 400/440, star connected, (but the motor may be delta...
Hi fellas,
I was wondering if somebody could help me with a wiring diagram please, it is an existing system that has had underfloor heating added.
The system is:
Oil fired fully pumped system ie
motorised valve on heating
motorised valve on the dhw
Addition:
Underfloor heating manifold...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc