clipping cables on damp proofed wall

[Daz]

Got a job rewiring a kitchen where the walls have been damp proofed with a membrane.
I have spoken with the plasterer and he is fine studding the wall out so that I can use drywall boxes but unsure of how to clip the cables as the nails will puncture the membrane.
Any ideas please?

 

[Leesparkykent]

Got a job rewiring a kitchen where the walls have been damp proofed with a membrane.
I have spoken with the plasterer and he is fine studding the wall out so that I can use drywall boxes but unsure of how to clip the cables as the nails will puncture the membrane.
Any ideas please?

Clip them to the stud that he installs.

 

[Daz]

I did consider that but wondered if there was any other way.
Will cable clips ruin the integrity of the damp proof?

 

[Leesparkykent]

I did consider that but wondered if there was any other way.
Will cable clips ruin the integrity of the damp proof?

Well of course it will if you pierce it. Why isn't clipping it the the new studwork good enough?

 

[Wilko]

I've not had to use them, but these might be worth a look :
2-Way Adhesive Base Natural 25 x 25mm Pack of 100 - https://www.screwfix.com/p/2-way-adhesive-base-natural-25-x-25mm-pack-of-100/38890?kpid=38890&ds_rl=1245250&gclid=EAIaIQobChMIy5ehkpnk1gIVCo0bCh213wJFEAQYAyABEgLeP_D_BwE&gclsrc=aw.ds&dclid=CMu9p6-Z5NYCFZOJ7QodSNELlQ

 

[Daz]

The plasterer is not available for at least two weeks at which point I haven't the space in the diary for the 1st fix.
Brilliant wilko thanks for that will grab some and some cable ties from the suppliers.
Pretty sure that will sort it only a small kitchen so not many outlets.
Cheers

 

[The Ghost]

See a lot them hanging off whatever surface they happen to have been "stuck" on. Bit like 3M tape on the back of LED strips.

 

[Rosco]

I've not had to use them, but these might be worth a look :
2-Way Adhesive Base Natural 25 x 25mm Pack of 100 - https://www.screwfix.com/p/2-way-adhesive-base-natural-25-x-25mm-pack-of-100/38890?kpid=38890&ds_rl=1245250&gclid=EAIaIQobChMIy5ehkpnk1gIVCo0bCh213wJFEAQYAyABEgLeP_D_BwE&gclsrc=aw.ds&dclid=CMu9p6-Z5NYCFZOJ7QodSNELlQ

View attachment 38730

These are useful but I only use them inside metal trunking using the fixing hole to keep cables tidy and easier for liding up. If I was only using the adhesive part I'd probably only have it as a temporary item e.g. Festoon lighting.

 

[snowhead]

Speak to whoever did the membrane and ask waht is acceptable.
I'd assume is got warranty which you may (will) void by bridging it.

 

[Rosco]

As Lee said clip to the stud then you know it's fixed the sticky pads are very hit and miss IMO

 

[The Ghost]

I wonder how the plasterer is going to fix the stud? Sticky pads? And do you think he will put the cables in the stud properly when it is put up? Unless you somehow put your cables out of the way of the studs and noggins.

 

[ruston]

The way I have seen it done is a new stud wall completely seperated from existing wall with at least a two inch gap and top stud to ceiling joists and bottom to floor joists , then built in traditional way . Plenty room for cable and drywall boxes.

 

[Midwest]

Adhesive backed mini trunking or just leave the cables in the stud work like other such installs.

 

[MJPD29]

It might not be so damp proof after

 

[Fox]

I wonder how the plasterer is going to fix the stud? Sticky pads? And do you think he will put the cables in the stud properly when it is put up? Unless you somehow put your cables out of the way of the studs and noggins.

The studs are fixed as usual (screwed into the wall through the membrane), but the plugs used are designed to seal the hole drilled (if this makes sense):

PermaSEAL Quick Plugs Bag of 100 - £36 - Membrane Fixings - https://www.permagard.co.uk/p-seal-quick-plugs?gclid=CjwKCAjw3_HOBRBaEiwAvLBbokZ35wOk3ZMFZWzLklcOLRcy8Tp-fTPrOEuKxEopFW9DQ6MAgx3mDxoCoeoQAvD_BwE

Op - clip your cable to the studs as you would with a normal stud partition wall and use the usual partition boxes for switches and sockets. However, some installers use slater's lat to mount the plasterboard onto in order to minimise the space lost in a room when installing these kits. If so, you may need to use shallower boxes, so be careful if you're specifying fancy accessories that require deep boxes!