Could a failed HW valve cause boiler to keep running? | on ElectriciansForums

Discuss Could a failed HW valve cause boiler to keep running? in the Central Heating Systems area at ElectriciansForums.net

lecky_bob

-
DIY
Joined
Jan 10, 2016
Messages
14
Reaction score
0
Location
uk
(Or that might be should a failed HW valve keep boiler running)

Woke up this morning to find the boiler still running even though all timers off (HW and CH). We have a simple S-plan CH/HW system with oil-fired boiler and a 2-port zone valve for CH and a 2-port zone valve for HW. Various thermostats around but all off - including HW thermostat.

Live feed was on to the boiler from the HW valve (stuck in open position). When I manually closed the HW valve (and so closed the microswitch), it broke the live feed to boiler and everything shutdown as expected.

Would one expect the HW sticking open to call for the boiler to keep going regardless of timers?
 
Last edited:
Were you in my house the night before? I had exactly the same mystery! I've never actually had the need to squeeze into the cavity where my system is to work out how it's configured but I noticed the boiler was fired late at night with all CH and HW controls to off, I just turned the boiler off and went to bed, seemed to have corrected itself by morning. In my case though I've got a Nest system and half wondered if it might have been an unintended symptom of an overnight software update.
 
Would one expect the HW sticking open to call for the boiler to keep going regardless of timers?
Yes I believe so. The outputs of the programmer via room stat, cylinder stat operate the two port valve motors (brown wire), not the boiler directly.
There is a permanent live feed (grey wire) to the two port valves, so if the motor sticks, the boiler can receive a permanently 'on' switched live.
 
Yes. The feed to the contact in the valve is permanently live, so it if jams open it will command the boiler on 24/7 independently of any other control settings.
 
Depends on whether the valve in question is a two wire or four wire version. If it's four wire (not including any earth wire), then normally the boiler would be controlled by a microswitch connected to the grey and orange wires.
 

Reply to Could a failed HW valve cause boiler to keep running? in the Central Heating Systems area at ElectriciansForums.net

News and Offers from Sponsors

  • Article
Join us at electronica 2024 in Munich! Since 1964, electronica has been the premier event for technology enthusiasts and industry professionals...
    • Like
Replies
0
Views
378
  • Sticky
  • Article
Good to know thanks, one can never have enough places to source parts from!
Replies
4
Views
947
  • Article
OFFICIAL SPONSORS These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then...
Replies
0
Views
1K

Similar threads

I
  • Article
Baxi system boiler and Opentherm Hello Does anyone know if its possible to connect an Opentherm thermostat such as a Nest to a Baxi 800 System...
Replies
0
Views
263
Ian777
I
T
  • Article
Indirect (Boiler Fed) Megaflo Doesn't Stop Heating Hi, I noticed yesterday that when my HW is on, that the boiler runs constantly... I even...
Replies
0
Views
236
techweb
T

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top