Help with Wylex board

[I Trippet]

Doing a CU change yesterday, having purchased an 8 way Wylex board and 6 Wylex miniature RCBOs recently, and was about to fix the board until sods law, it's a stud wall and the screw holes don't align with the vertical battens. Decided the easiest thing to do would be get an 11 way. As I was working a bit far from my usual wholesalers I got one from a local CEF, took it back and fixed to wall no problem. As soon as went I went to clip the first RCBO in....... ----, realised it was a half din rail with nothing for the breaker to clip onto at the bottom. Rushed back to CEF and the guy who to be fair was very helpful looked into it and said it was a different model of breaker I needed, but guess what..... they don't have any!! Advised me to try other wholesalers in the area, but none could help and they were all perplexed as the number for the RCBO I apparently need is the old type and the board I bought was brand new!

I was able to fit the breakers for the time being by but they are only secured at the base by being screwed to the busbar and I cannot leave it like that. I'm being searching Wylex's range of products online all morning but I'm still non the wiser. Have Wylex in their infinite wisdom gone back to half DIN rail assemblies, without updating their range of breakers, or am I missing something. Much appreciated if anyone can help me.

 

[buzzlightyear]

it's a stud wall and the screw holes don't align with the vertical battens.

Easyfix Self-Drill Plasterboard Fixings Metal 32mm 100 Pack - https://www.screwfix.com/p/easyfix-self-drill-plasterboard-fixings-metal-32mm-100-pack/2422h.

 

[buzzlightyear]

having purchased an 8 way Wylex board and 6 Wylex miniature RCBOs

and which range was this .

 

[snowhead]

With the full din rail the busbar is floating.
With the half din rail the busbar is secured to the backplate.

 

[Vortigern]

Could you put some din bar in the CU?

 

[HappyHippyDad]

I would have used plaster board rawl plugs, the metal screw in ones. Man, you've gone to a lot of trouble for the sake of a rawl plug ?
Or possibly screw a piece of ply on to the wall into the joists, it would only be a little bigger than your original board.

 

[I Trippet]

The original board I'd got was an NM606FLEXS and the breakers are NHXS1B. Board I got was NM1106L.

 

[I Trippet]

I would have used plaster board rawl plugs, the metal screw in ones. Man, you've gone to a lot of trouble for the sake of a rawl plug ?
Or possibly screw a piece of ply on to the wall into the joists, it would only be a little bigger than your original board.

Normally I would but they would have been too close to the hole for the cables

 

[UNG]

That's why I always have a piece of 12 or 18mm ply or OSB and / or some 50 x 25 batten handy when I am changing a CU on a plasterboard wall, not sure I would be using plasterboard fixings to fix a CU

 

[Zerax]

I wouldn't use only plasterboard spirals to fix a CU... but I would use them to secure a piece of board to the wall with some grip fill behind it... essentially the grip fill is bonding the board to the wall and the spirals are just holding it up until it's gone off.

Plywood is a very handy thing to keep in the van... I use it in preference to softwood for making little noggins to screw plasterboard to for hole covering.

 

[Mike Johnson]

Most DIN rails are removable, could you not just change the new CU rail for a compatible one?

 

[multimick]

Try drilling new holes .you don't have to use theirs

 

[Mike Johnson]

Try drilling new holes .you don't have to use theirs

Is that within the manufactures guide lines for using their enclosure. ?

 

[multimick]

No difference drilling extra holes in back of enclosure to knocking out 20 mm holes in bottom and putting grommets in

 

[MJPD29]

I never ever use Wylex. Far too many different breakers for different boards. Why can companies like hager maintain the same design or at least design them to fit previous boards also? Money making scheme from wylex