It's Just Not My Day...... | Page 4 | on ElectriciansForums
Guest viewing is limited

Discuss It's Just Not My Day...... in the UK Electrical Forum area at ElectriciansForums.net

Paul.M

-
Supporter
Joined
Aug 23, 2010
Messages
10,384
Reaction score
5,808
Location
Lost in Space
.... Slept in, an hour late to pick up the "mate" (not a good start).

Later on showing him how to put up some door coach lights and drilling from the outside, this happened:-

[ElectriciansForums.net] It's Just Not My Day......

Whoops :rofl:

Within an hour this happened:-

[ElectriciansForums.net] It's Just Not My Day......

Yep,,,, that is my right leg hanging through the ceiling of the living room! I was looking up at the light fittings and not looking where I was walking! Think I may have to slip the plasterer a couple of quid to sort it out lol :rofl:


Enough is enough so we packed up and quit at 3pm. Tomorrow is another day :smile:
 
As an apprentice, I was working at a boarding school. We were rewiring the dorms, and brickies putting up some new walls. I was in the loft space, electrician below. As I stepped onto the joists towards the large loft hatch, I slipped falling thru the hatch. I managed to catch the edge of the hatch door, but the effect caused me to swing like a gymnast on bars, with my feet knocking over a recently laid block wall. Brickie tried to kill me. Electrician said I wasn't allowed in the loft anymore.

Following week, we were putting up some new light fittings in the sports hall. Electrician was in the loft space, to postion the wood battons for the lights, I was pushing the tower scaffolding around and screwing up the new lights. I had just got down off the tower to move the next position, when I heard a crash and a loud scream. Looked up and saw the electrician hanging from a hole in the hall ceiling, with him yelling to get the tower under him.

We never spoke about it!
 
Cored an 18" wall only to find I'd also gone through a 4" waste pipe, dead centre mind so out with a few bricks wrap a rubber gasket around pipe jubilee clip it, cement bricks back in & skim wall. also dropped in a bit of duct to save having to core in a new place.

Drilled through wall into a ply internal door that had been left open.

Cut plaster board for a back box & found the microbore pipework running diagonal across the wall.
 

Reply to It's Just Not My Day...... in the UK Electrical Forum area at ElectriciansForums.net

Recommended Sponsor News

Quickwire Now Sponsor ElectriciansForums.net

I am sure you will join me in welcoming our newest sponsors of ElectriciansForums.net - Quickwire! They have decided to join us after seeing you guys discussing their products here. Now we have an expert on board that you can chat to @Quickwire-Sam who will be happy to answer your queries!

[ElectriciansForums.net] Quickwire Now Sponsor ElectriciansForums.net


@Quickwire-Sam said "At Quickwire, we're all about speed, safety, and reliability. We're a family-run business, and every Quickwire connector is proudly made right here in the UK, ensuring noticeable quality. In short, Quickwire is the fastest connection method on the market. Whether you're an experienced electrician or a DIY enthusiast, Quickwire makes electrical connections ridiculously quick and easy. We're passionate about blending British craftsmanship with innovation. If you have any questions or if there's any way we can help, please just ask me!"

Exclusive Forum Offer! Free euro 2024 wall chart for first 10 responses!

Hi everyone,

We have 10 exclusive Uheat EURO 2024 Wallcharts to giveaway for Electricians Forum Members! The first 10 people to reply YES to this thread - I will message and get them sent out to you just in time for this years tournament! GO GO GO

PCBWay Now Sponsor ElectriciansForums.net!!

I hope you will all join me in welcoming our newest sponsor to the forum PCBWay! You can contact their friendly people by sending a message to @PCBWay who will be happy to answer your queries.

Welcome to the community and thanks for your sponsorship!

[ElectriciansForums.net] PCBWay Now Sponsor ElectriciansForums.net!!

PCBWay provides services including PCB Prototype and batch Production, PCB Assembly (SMT), 3D Printing, CNC Machining, PCB Design, Electronics Modules Selling, etc. We are committed to meeting the needs of global makers from different industries in terms of quality, delivery, cost-effectiveness, and any other demanding requests in electronics.

[ElectriciansForums.net] PCBWay Now Sponsor ElectriciansForums.net!!

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Thread starter

Paul.M

Supporter
-
Joined
Location
Lost in Space

Thread Information

Title
It's Just Not My Day......
Prefix
N/A
Forum
UK Electrical Forum
Start date
Last reply date
Replies
47
Unsolved
--

Thread Tags

Tags
None
This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top