meters not accurate below 0.01 ohms

[peterhardacher]

After previous thread on here regarding. Max Zs when getting to the bigger fuses 400 amp + max ZS is below reading range of meter R1R2 0.01 ohms I have told this to my boss who is not giving me no feedback now I. Am the only tester on site no one else to ask really. Now I really would like to know the procedures other testers follow and or equipment used for these situations . As I want to make sure my work practices are what the standards require and equipment I test is safe and correct testing equipment procedures been followed so I can be certain that when I have tested it its safe to use or in the other case could be unsafe the last thing I want is anyone getting hurt

 

[telectrix]

a thread was psted some time ago, suggesting a resistance was used in series with 1 lead. then subtract that resistance value from your reading.

 

[peterhardacher]

The scale on the meter is only 0.00 so even if u done that and had a 0.02 resistance lead your readout won't register cos it's smaller than 0.01 ie 0.096 for a 400 amp thanks for ure input though its got me thinking

 

[Guitarist]

If you are solely responsible for this testing, but are not sure exactly what procedures to follow, can I suggest that you ask your boss to sign you up for a refresher course to give you the confidence to test what is required of you. The instructors will also help you decide if new equipment is needed, and you can stop worrying.

 

[peterhardacher]

I am competent and not worried I am just trying to get input from other electrical testers there is nothing hard about what am doing and going in a refresher purely to ask the question I have asked now is is not nesrcery . And as u are aware 2391 is a course designed round the house bashing industry . I think the question I have asked is a valid and responsible one as I don't remember covering fuses etc outside the scope of the regs . All I am doing is asking other industrial electricians for there input as I am on my own here if I was not I would ask one of the old boys as we do in our industry as one person does not know the ansure to everything , and guitarist do u know the ansure to what am asking I don t think u do instead u make a sarcastic comment instead to try make ya self seem clever guess u know it all . That is what is wrong with are industry these days we should be helping each other out as sparks and union brothers but guess my way of thinking is one of the few

 

[peterhardacher]

When I said what procedures to follow I was not talking bout how to test I was talking if your Meter does not allow a acurate test ie calculation and like the first reply to my thread some guys use a resistance on the meters hope the first post was not misleading in what I was asking about testing is not the problem the meter itself is and after u have reported this to management they say its fine I would like to go back into the office next time with some valid points for my argument

 

[telectrix]

i can't see what the need to measure <0.01Ω

 

[peterhardacher]

Max ZS on a 400 amp fuse for a 5 s disconnection time is 0.096 and higher fuses are. Lower

 

[Guitarist]

I am competent and not worried I am just trying to get input from other electrical testers there is nothing hard about what am doing and going in a refresher purely to ask the question I have asked now is is not nesrcery . And as u are aware 2391 is a course designed round the house bashing industry . I think the question I have asked is a valid and responsible one as I don't remember covering fuses etc outside the scope of the regs . All I am doing is asking other industrial electricians for there input as I am on my own here if I was not I would ask one of the old boys as we do in our industry as one person does not know the ansure to everything , and guitarist do u know the ansure to what am asking I don t think u do instead u make a sarcastic comment instead to try make ya self seem clever guess u know it all . That is what is wrong with are industry these days we should be helping each other out as sparks and union brothers but guess my way of thinking is one of the few

That was just rude, and totally unnecessary! I wasn't trying to be clever or put you down. It's replies like this which make me feel like I don't want to bother helping anyone. Maybe look at yourself before moaning about others not helping.

 

[peterhardacher]

Well suggesting some one goes back to college is a Help full ansure ???? If u feel it is I would be glad u don t reply on anything am not being rude one bit usually the lads on here are helpfull and knowledgable , and do u know the ansure cos that would be help full cos s lot of experienced sparks don t should we all go back to college . It's type of testing lot of people don t. Come across not in commercial or house bashing its heavey industrial petrochemical

 

[telectrix]

to be fair though, your OP was not that clear. at first glance it appeared that you were unsure of your testing procedure.

 

[peterhardacher]

Yeah I know should have been more clearer hope my other posts cleared this up a bit don t want to come across as bein a --- but just bit at the comment I think this is a good forum and I will offer advise when I can cos I have had some good advise myself . Which brings me back to the orginal question lol guess I will have to get on Internet tomorrow do some research and contact suppliers of test equip

 

[telectrix]

does make you wonder, though, why these values are called for when there's no means to measure them. perhaps there' are meters available at stupid prices that will have a resolution low enough.

 

[peterhardacher]

I know yeah there has got to be or maybe by calc ?? I will know more after this weekend research haha then I can be in a position to refuse to test or note down on test sheet instrument won t test as u know ya signing a legal binding document and if anything did happen the first question they would ask why you signed it ok dangerous territory lol

 

[telectrix]

one way would be to measure the cable/s with a tape measure, then calculate the resistance from the mΩ/m tables.