Name this device

[Octopus]

Customer thinks it was installed in 1964 when the house was built!



Thanks

 

[Knobhead]

These were used as isolation switches by that world renowned bathroom company Dolphin

If you have ever opened up a original Dolphin shower,the sneaky lads at Dolphin design pinched these breakers to use as isolation switches for their showers

Would you believe they had a fancy looking piece of string linked to the elcb which was mounted side ways on and a glass front to hide the dirty deed

If you come across one again Des, have a closer look. The same chassis was used for MCCB’s. They all have 3 blind 2BA mountings holes on the front for panel use.

As for Dolphin I'll keep quiet. Bunch of &&& ^%$&* &$^*&(^% *&^

 

[JonNewbie]

Hello, new here, but have a similar question... what is this? Is it a three phase version of the same thing (VOELCB). It says Crabtree, but not much else. And yes, the line conductors colours don't match!

 

[timhoward]

I believe that is a 3 phase earth leakage circuit breaker with overload protection. A kind of primitive RCBO with different leakage detection method, relying on a coil between real earth and installation earth.
Under the stickers there once would have been a plate that told you exactly what it is. See example of another one below.

I'm sure you already know that it needs taking out of service. And as the stickers read like a list of special locations with special requirements this one may need more than a little thought.

If you remove it, save it, as collectors might like it!

 

[pc1966]

It looks like it.

Also something to have checked professionally to see if you have adequate protection for the installation as a whole since VOELCB have a number of issues, one being they are generally old and may not be tested (have you test tripped it?) and the other being that any additional earth bonding can make them ineffective at detecting a fault.

The other worrying sign is the apparent shuffling of phases!

It might be that device is now largely redundant if the distribution boards have RCDs in them providing the required level of protection, but I certainly would suggest it is checked. Do you have photos of the board(s) the device is feeding?

 

[JonNewbie]

It looks like it.

Also something to have checked professionally to see if you have adequate protection for the installation as a whole since VOELCB have a number of issues, one being they are generally old and may not be tested (have you test tripped it?) and the other being that any additional earth bonding can make them ineffective at detecting a fault.

The other worrying sign is the apparent shuffling of phases!

It might be that device is now largely redundant if the distribution boards have RCDs in them providing the required level of protection, but I certainly would suggest it is checked. Do you have photos of the board(s) the device is feeding?

Thanks Tim & PC!!
The device feeds a 3P 63A switch fuse next door to it, then a long run of armoured cable to a modern 3P board, with RCBOs. Apparently the device is tripping once in a blue moon when there is a lot of load on. Sounds like from what timhoward says, it may be overload rather than leakage that trips it?. Sadly the plate is no longer there.

 

[pc1966]

The device feeds a 3P 63A switch fuse next door to it, then a long run of armoured cable to a modern 3P board, with RCBOs. Apparently the device is tripping once in a blue moon when there is a lot of load on. Sounds like from what timhoward says, it may be overload rather than leakage that trips it?. Sadly the plate is no longer there.

It sounds like it, though of course enough accumulated leakage might trip a RCD-like device (though on 3P a lot of the would cancel so really it would be imbalance on leakage).

If this is a TT set up then the sub-main would need some sort of RCD protection as a L-E fault there would probably not take out any supply OCPD. As there is a switched-fuse for overload (I guess?) all that would be needed is a delay RCD. Also it probably falls in to the special locations where <= 300mA RCD for fire is required.

If it were my business I would look at replacing it with a 100mA or 300mA delay RCD in a suitable enclosure.

 

[timhoward]

It could be overload tripping it. Or it could be a fault with a distribution cable. I'm afraid it really needs looking at.

These devices are often found where the earthing for an installation is a rod in the ground (known as TT), and the original job is turning things off safely if there's a fault. With this kind of earthing it's very important to have a device like this as not enough current will flow to operate the suppliers fuse under fault conditions.
Anything between the RCBO's and the origin are probably relying on this for fault protection, and even if it's working it really needs replacing with a modern RCD.

 

[timhoward]

This might be helpful to illustrate the point: (First 6 minutes will do.)

 

[JonNewbie]

It sounds like it, though of course enough accumulated leakage might trip a RCD-like device (though on 3P a lot of the would cancel so really it would be imbalance on leakage).


If it were my business I would look at replacing it with a 100mA or 300mA delay RCD in a suitable enclosure.

Thanks PC! Yes, it's TT. I was thinking 300mA type S. So much hanging off it, 100mA could nuisance trip, even with everything on 30mA RBCOs. I think they left this in as they did not want to mess with the meter tails...

 

[westward10]

STD stands for Short Time Delay.

 

[telectrix]

STD stands for Short Time Delay.

back in the 70's, with BT it was Subscriber Trunk Dialling.
now with the sawbones, it's Sexually Transmitted Disease.

take your pick ( or if your Irish, alternate with a shovel ) .

 

[littlespark]

So even a decade old thread can be informative.

I see the labels on the thing mention tractor shed…. So, on a farm? Likely never been tested.
But also cafe? So an area open to public… let’s hope there’s rcd protection in there at least.

 

[bill01803]

Anyone still got their Clare tester for the ELCBs?

 

[GLENNSPARK]

I believe that is a 3 phase earth leakage circuit breaker with overload protection. A kind of primitive RCBO with different leakage detection method, relying on a coil between real earth and installation earth.
Under the stickers there once would have been a plate that told you exactly what it is. See example of another one below.

I'm sure you already know that it needs taking out of service. And as the stickers read like a list of special locations with special requirements this one may need more than a little thought.

View attachment 94275
View attachment 94276

If you remove it, save it, as collectors might like it!

Disconnect the in/out earthing polls....and keep it to use it as an on load isolator...
As the contacts in it are capable of making/breaking full load rating...