Need help finding fault | on ElectriciansForums

Discuss Need help finding fault in the UK Electrical Forum area at ElectriciansForums.net

Joined
Jul 7, 2021
Messages
2
Reaction score
0
Location
perth
Can some one please help with this. I am getting 11v on two light circuits, it should be 240v Other lights in the circuit are working OK, it is just the hallway light and bedroom light that do not work. I have opened up the two switches and batten holders to check for loose wires but everything looks OK. So why would the circuit only have 11v on it? I assume it is a loose wire some where, are I correct?
 
What are you using to meet sure the 11v and what are you measuring between?

Hobby type multimeters are not calibrated and could give false readings when measuring.

If lights are not working, then check bulbs, check connections, check other recent work hasn’t drilled through a cable.
 
using a $200 multimeter, I have removed 2 batten holders (light fitting) and 2 light switches and there are no loose wires. Bulbs are OK but will not work on 11v, as they are rated 240v. I am getting 11v at the batten holder and switches. Owner said lights started flickering then went dead.
 
junction box above ceiling? a terminal in a batten or a switch witth screw clamping insulation? a conductor broke right in the terminal so you can't see it, but a tug would find it?also, measure volts Line - E, if thet reads 240V, then you have a broken neutral
 
using a $200 multimeter, I have removed 2 batten holders (light fitting) and 2 light switches and there are no loose wires. Bulbs are OK but will not work on 11v, as they are rated 240v. I am getting 11v at the batten holder and switches. Owner said lights started flickering then went dead.
Yes but where are you measuring from to get 11v? L/N L/N etc
 
My guess would be no Neutral, break out the wander lead and do an rN from the board to the fittings.
Edited to add, with my equipment I'd check voltage L-E and L-N to confirm this, 240V L-E would strongly indicate a lost Neutral.

If, as suspected you have an open circuit, you need to start looking back along the circuit checking rN until you have continuity.

Your fault will be between here and the faulty fitting.

Have any lights/switches been altered in other rooms?
 
Ah… just checking. OP is from Perth Australia, not UK… so try and give “region free” advice ?
"have a cold one". is that region fre advice?
 

Reply to Need help finding fault in the UK Electrical Forum area at ElectriciansForums.net

News and Offers from Sponsors

  • Article
Join us at electronica 2024 in Munich! Since 1964, electronica has been the premier event for technology enthusiasts and industry professionals...
    • Like
Replies
0
Views
707
  • Sticky
  • Article
Good to know thanks, one can never have enough places to source parts from!
Replies
4
Views
1K
  • Article
OFFICIAL SPONSORS These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then...
Replies
0
Views
3K

Similar threads

I'd always go for 25mm2 5core over 50mm2 3core, with the cores paired up. Considerably cheaper, easier to terminate and ready to go, if ever 3...
Replies
7
Views
431
  • Question
I would add though that a typical good TT rod of 100 ohms only needs 3V to have 30mA flowing and so trip an RCD, you might find that sort of N-E...
Replies
8
Views
738

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top