So wiring in campervans is included within the scope of BS 7671. In a scenario where someone is being paid to build from scratch or modify a system, is there a minimum level of qualification required by law?
Would a "Part P NICEIC domestic installer" be appropriate to carry out and certify the...
Greetings. I have generator with only 120 V output. It has both standard 120V outlets and a TT-30. A friend's cabin is wired for alternative generator power with a transfer switch to be used during power failures. There is a L14-30 male receptor on the outside of the cabin which connects to the...
Hi all, been called out to a job today where the customer says they are getting a tingle from the gas meter and some appliances. Its a TT system, got a ze of 48 ohms. Gas bonding is 10mm and is continuous. Dual rcd board with 3 RFC's on one side of the board. There's a L-N reverse when i go...
220 vs 240 outlet questions
I have a question understanding the difference between 220 volt outlets and 240 volt outlets. I saw a video online of someone adding, as the video describes, 220 volt outlets to their shop. He opens the panel, and obviously by means of a double breaker, connects both...
Hi
I'd like to install a 240 volt single phase sauna stove at a distance of about 200 ft from my main panel. The main panel has a 40 amp GFI breaker and an 8/3 exterior wire that goes into a sub panel in my workshop. The 8/3 is inside of a black 1" pvc 50 ft long flexible water pipe. I'd like...
Hi... I am Shamsul from Malaysia
I have a question regarding to earth fault current if occur inside 240V single phase customer house/building
1.May explain how the earth fault current flow route
2.If got local earthing was connected from ground to 11kV 3phase DEAD line, is it the fault current...
Hi Guys,
Wonder if I may ask a question?
Is it permissible to run the red fire alarm cable with the mains T&E cable, though holes and in the same trunking?
I thought alarms were 24V and that ELV, data, telephone etc & LV should be kept separate?
Maybe there is an exemption for fire alarm...
Hi guys, struggling with a problem wondered if anyone can help.
Had 2 A/C units failed on me, spare parts not available til end of August... :-(
The faults were caused by the fan units which vapourised tracks on the PCB, great design , not.
I can repair the PCBs but the fans are dual fans...
A client asked me to fit some LED strip lights, 1m long, easy enough, they bought them, probably on Amazon, 3 pin plug with 6 inches of wire and then a very small plastic enclosure about the size of a switch, then another 6 inches of wire directly into the strip lighting. I needed to extend the...
Hi all,
I have a charger that is fitted with a 240v rated 2p+E male inlet and a matching 240v rated female plug. However it is connected to a charger that is rated for 110V as it will be operated in the US. Is there an issue (if any) with supplying 110v Ac mains paired with the 240v rated plug...
Hi,
If i had a 240v rated garden post light, powered it with 24v and used an e27 24v bulb, would it work?
I want 5 garden posts, and there's a nice one for 14 quid but it's 240v.
thanks if you can help :)
Hi guys - Looking for regs on how socket wiring should be routed. Cant see this in the Part P or any of the other building regs. docs. Anyone any pointers on the corresponding rules? Need some guidance on routing socket wiring vertically and also horizontally as need to use both methods.
Good Morning.
I have a fused spur which has 2x240v inputs and 1x240v out put.
The 240v inputs are from heating control panels. One is from a timer clock for hot water and the other from a large 1000l hoh water storage tank. The ouput is to the oil burner.
So the question is when i have i...
Hi all,
last week I decided to start painting the inside of the house and began in the kitchen. So to paint the ceiling, I lowered all LED downlights and left them prised using the spring loaded mechanism allowing to paint under the gimbals, so no weight was placed on the wiring whatsoever...
Hi,
Hoping you all can help me wire up my single phase 240v induction motor. Can someone please explain or even better sketch out where the wires need to go, I have a fair idea already just want some good advice before I continue.
Switch is CK-5 10A 250v - SWITCH
Thanks in advance!
I just replaced my range with a new one because the old oven took a long time to get hot and then eventually stopped working all together. Assumed it was an issue with the range as it was 20 years old. Hooked up the new range and the control panel was flashing and could not turn oven on. Could...
Hello,
I am renting a room to a friend and he will put an EV charger to charger his Tesla. Please advise for a good 240V meter that I can put the meter between breaker box and charger unit so I know how much kw he use each month and I will calculate how much he have to pay for electric.
Thank...
Went to National Lighting today to find a mini downlight for shelf lighting in bathroom. Gent sold me a IP67 240v fixture. It was my understanding that 240v was not allowed in Zone 1 unless a shower unit or pump etc. Someone want to clear this up for me.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc