I need to install a sub-main supply cable from the house to a shed approx 100M away. The SWA needs to be 25mm csa for volt drop requirements - I intend to install a 100mA RCD and 40A MCB to protect the cable for overload / fault protection using the armouring as a means of earth. Then with the...
elbar
Thread
2 core3core
aus
cable
core
electricians' talk
main
supply
swa
My local electrical shop was out of stock of 1.5mm 3 core flex but offered to sell me the normally more expensive low smoke or heat resistant alternative for the same price. I have bought some but it is a lot a thinner than any 1.5mm I have ever used in the past or see in other shops now, its...
Cinquestelle
Thread
3core
aus
core
electricians' talk
flex
smoke
standard
On a standard hall & landing 2 way circuit (i.e both switched from either location), does everyone prefer using the 3 core method, with each light being fed by the appropriate circuit (i.e upstairs / downstairs) - are any other methods in current use?
jase31
Thread
3corecore
electrical
electricians' talk
light
light switch
method
methods
switch
switches
two way
wiring
socket ring wired in 3 core and earth - seems to be 2.5mm in old colors - the third core is blocked at each end. do sockets have to be in 2 core and earth or not? As the ring is being extended is this all going to be have to taken out.
midgetman
Thread
3core
and earth
aus
core
earth
electricians' talk
ring
used
Morning all
Other than my local TLC, nowhere seems to stock "3 core 4mm flex".
I was connecting a new cooker up yesterday, and the manufacturer recommends "3 core 4mm flex" as a minimum spec.
Now on a Sunday afternoon, not much chance of finding any of that, so I used some 6mm T&E that I...
I'm adding a outside light to an. Existing install. The lights have been wired in an rb4. Can I add my light fitting to the circuit but wire it in 3 core flex instead of 1.5 twin and earth?
I have just been on a site inspection which produced burnt out cables (Sheathing melted or burnt away), within some ground recessed fittings. I have not seen this used before and can only find reference to this cable (SY Cable) being used for Air-con, IT and food processing as a 'control' cable...
Bright Sparks
Thread
3core
along
aus
cable
core
domestic
electricians' talk
fittings
halogen
lighting
method
outdoor
Hi All,
First thread in ages.
Recently went to a a pub to carry out some origin tests before they begin a total refurb.
It used to be a 3-PH supply / metering but they are only using 1-PH (red) with single PH metering.
I opened the service head to discover a core cable swa cable...
Now then, for a single phase circuit, using a 3 core SWA having brown black and grey conductors... I always think that you should sleeve the black with G+Y to use as earth, and sleeve the grey up with blue to use as neutral.
I cant find it in the regs or any of my other books, but I thought...
Hi everyone,
just reading and giving myself examples of cables etc to work out cable selection and volt drop ( I know its Friday, but I have to keep reading or I will forget )!!!
If for example you have an swa 3core (brown, grey, black), which , say your running to a supply from a DB board...
I dont do a lot of external works, however, I have been asked to install some power for general lighting and powerto an outbuilding with no extraneous conductive parts 15 meters from the main board and my thoughts were;
The supply is tt, so 10mm 2 core swa from spare way in main board to CU in...
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc