am2 | Page 9

am2

Recent contents View information Top users
  1. R

    Am2 exam failed on LIVE testing any guidance or help?

    Hi All, Ive just got my results through and I failed my first attempt of AM2 exam on the live testing of inspection and testing. I passed everything else just the live testing simply all because I ran out of time that was allowed for the inspection and testing. So Im gonna try and get re booked...
  2. J

    Am2 IR test failed on the global test

    hi all, Failed my AM2 on IR test. Just a query do you have to remove both the nuetral and the cpc fly lead from RCBO when doing a global test? I did this but I did not put the cpc from the ring final in to the MET bar. I tested the ring circuit, motor and strappers separately. That’s the only...
  3. R

    First Day of AM2 exam finished! Just need alittle bit of help.

    first day done of my AM2 exam. Just wanted to let people know what I done and if I will loose any marks. So first of all risk assessment and safe isolation. I completed the risk assessment no problem at all and the safe isolation I completed fine as well asked for permission to isolate, prove...
  4. R

    AM2 exam is Monday Morning Need Help with PFC testing on 3 phase and rcbo testing on lightingcircuit

    Hi everyone, Not going to lie I am crapping my self for my AM2 exam on Monday Morning at 8:00. So I just need a few questions answered:- tell me if I am right or wrong. I will be using a megger tester by the way. PEFC testing 3 phase ( 3 probe test) :- Clamp croc clip on the neutral bar...
  5. R

    Just had Refresher Course for AM2 Exam is Monday need help with PSCC and PEFC!

    I have just been on the refreshers course for the Am2 exam that I am about to sit on Monday coming. When the tutor was going over PSCC and PEFC. I was confused, completley thrown. So in my head I would do:- I would carry out this test on the Incoming Tail side of the 3 phase board? PSCC:-...
  6. R

    Am2 Monday Coming NEED some guidance on motor circuit testing etc...

    Hello all Sparkies, Ive got a question how would you measure Zs on the installation at the origin? Even though the install is “dead”. How do you test the motor circuit as in IR and Zs etc? Would you test the 3 phase IR from the supply to the contactor then do the same from the load side to the...
  7. R

    Am2 exam question bonding cable tray/ metal trunking?

    Hi everyone, I am sitting my AM2 exam a week today and was wondering if the metal trunking, cable tray etc needs bonded back to the MET in the board? Will you fail if its not bonded or will it be a minor? Anyone got any ideas? Thanks.
  8. R

    AM2 Exam in a week time any tips or advice?

    Hi all sparkies/apprentices, A quick introduction I am currently a electrician apprentice with a domestic contractor just a small business. I have now complete my NVQ side of my qualification now sitting the dreaded AM2 Exam on the 12th Febuary until the 14th. However, I do have the refresher...
  9. B

    AM2 general questions

    just about to book my AM2 as a final part to get myself approved. What do I need to brush up on? I’ve recently bought the regs book even though I know the 18th edition is due in June o_O and have a well thumbed on site guide somewhere, am I right in it being open book on the theory side...
  10. J

    Am2 safe isolation advice

    Hi everyone. I am currently doing my am2. Did they safe isolation today. Not sure if I messed it up. For some reason I took the protective neutral cover off from the board then performed the 10 step isolation. I asked permission to isolate, labelled with warning signs and put key in pocket...
  11. J

    Testing and inspection on am2

    hi all, Have my am2 next week... just brushing up on a few things. Was looking for some advice on IR test on the whole consumer unit with a RCBO. Is it ok to just remove the fly leads from RCBO or is it ok to disconnect and test live to neutral, live to earth, earth to neutral etc from the...
  12. C

    Any tips for my am2???

    hi there I have my am2 tomorrow and was just wondering if anyone had any tips for me? Thanks in advance
  13. C

    Am2 lighting confusion

    hi there I'm new to this today but I was wondering if anyone could help, I have my am2 on Monday and I can wire an ordinary 2 way intermediate circuit no problem but on my precourse the said that I need to take a neutral to every switch using t+e and was just confused to how I would do that...
  14. B

    AM2 fault finding today

    AM2 fault finding today wish me luck
  15. B

    AM2 fault finding help

    Hi don’t do that much fault finding and could do with some help, AM2 7 faults to find using on a continuity tester so can only be one of four things, but not really sure what readings to expect? Short circuit = tester should show a few ohms but may have some resistance in leads and bleep Open...
  16. B

    AM2 lighting circuit

    Hi got AM2 in a few weeks, on the build there’s a 2 way and intermediate to wire up, I know how to wire one up but the way they want it doing is not the way I have ever done or the way I would do it, you need a neutral at every switch, from DB to first switch in T+E then 3 core to intermediate...
  17. J

    AM2 resit help 2017!!

    hi everyone. I'm resitting my am2 in a couple of days for the install and I&T. I failed my install last time because my ring was incorrect. I was told sometimes the assessor will un-do a cable and you are supposed to check it...(is this true) and that may of failed me. I know this is a very...
  18. Liam fenwick

    New member am2 exam end of month

    hey I'm a new member to the site I've been doing electrical work for about 1 year and a half now and was an audio visual installer before hand. I completed my level 2 and 3 2330 city and guilds electrical course straight out of school but never found an apprenticeship in electrics bu ended up...
  19. jordanlewis88

    AM2 Pass or fail advice

    Hi all, I am pretty new to this group so forgive me if this thread is already someplace else but i have just finished my second day of my AM2 online exam done, installation done, and part of my testing done ( just have to complete paperwork) Theres a few minor things i know are wrong with my...
  20. foufou

    AM2, NVQ3 changing provider

    Hello everyone, I have done my profiling for my NVQ with a provider, and paid already the fees for my AM2 and I'll do it in august, however I'm not really happy with this provider for my portfolio as the assesor is not helpful. I would like to know if it's possible after I have done my AM2 to...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top