Hi everyone,
I’m looking to disconnect a noisy ceiling exhaust fan but I want to be able to reconnect it easily should I ever sell. I’ve attached a picture of the wiring from the roof to the fan. Can I simply cut the brown and black wires that are soldered on?
Hi all.
just about EFLI testing.
as3000 table 8.2
As it is titled- EFLI of total circuit
Is it my understanding that if I use the table for testing EFLI for a sub circuit say a 10a circuit I can test and check the reading. Then I can also test the sub main and again use the same chart or...
Hi,
recently completed my cert lll gap training. From the uk and been in Australia for two years.
I am just asking for any advice as I would like to get some further Experience and knowledge of qualifications I will need or the best advice in gaining the skills.
Thanks in advance
Hi guys I've gone the mining route for the last 20 years and as such I'm a bit rusty on the domestic side of things.
Anyways my questions are:
1. in a domestic household, do we still try to have 2 lighting and 2 power circuits mixed?
2. What form of RCD is everyone using right now?
Is it 2...
To my fellow Australian or Kiwi Sparks is there any stipulation on using Wagos rather than BP’s in the AS/NZ 3000? Can’t seem to find anything and they’re starting to sell them here.
Hi Guys,
First post here and I am encountering a very weird issue I havent seen before and am struggling to work out.
I recently did a few upgrades at a home including a new DB and earth stake. The home is split with half power run under the home and half power and lighting run above the home...
Hi there my name is david. I am a qualified electrician working in scotland. Up to date and got my 18th edition regulations qualification also. I work in domestic. Done house bashing 1st fix and 2nd fix for years and now mainly do contracts new kitchens. bathrooms and maintenance. How easy is it...
Hello,
I am currently working on a project that previously utilises a charger for a battery system that is connected via single phase 240V AC mains. The existing charger has the 15A inlet running through a 1P 16A schneider MCB with the active line connected to the MCB (with earth and neutral...
Hi Guys,
I was wondering if I can get some advice on some stairway LED lights.
These lights are approx 5 years ago and has all except for one has been failing. Upon closer inspection, I realise the entire housing is wired and the LED component is solder on.
I was wondering if its possible to...
hey guys
had to replace the VFD on my lathe. running off 240v single phase to 3 phase to control the motor in delta config.
i wired the new vfd up as per the last one, which is a different brand. hooked up active and neutral, then the ground to the chassis screw, when plugged in instantly trips...
12 volt switch help.on my motor home has a short somewhere ,I’m thinking maybe in electric step switch. Iv wired a standard rocker switch ,goes back to centre when not pressed .just runs the 12 volt motor for the step. Iv got on the top row of switch ,earth on left and positive on right and just...
Hi,
Just a question from AS3000 max demand diversity table C1 for instantaneous hot water. Will it be the same diversity regardless if it is 3Ph or 1Ph or higher current rating or less?
Hi Everyone, I have a steel framed shed and noticed it uses the earth from the house via a 10mm 5 core cable. I cant see anywhere where the shed frame is physically earthed, the earth wire in the five core cable goes to the distribution panel in the shed. Should the earth wire also go to the...
Please could you comment on this installation on this 240v supply, particularly on the outer sheath stripped back on the orange circular, any reference to AS 3000 would be appreciated
Hey guys
My partner and I will be moving to England in a few months for around a year or so. I'm a fully qualified electrician in Australia and I'm aware of the steps I need to take to become qualified in the UK. I was just wondering if I could get a job doing security cams or door access...
Hello guys,
I'm currently working in the UK as a Electrical Maintenance engineer in the food industry. Me and my partner are talking about a move to Australia or New Zealand and there seems to be plenty of jobs when I've looked but I'm not sure where to start.
I'm only BTEC level 3 qualified...
Hi people,
I'm carrying out an online course to gain my qld electrical licence.
Been a good while since calculating cable length using equations and regs books.
Can anyone guide me to the correct equations please
Thanks in advance
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc