Hi All,
Regulation 411.7.1 states that the provisions described for Regulations 411.7.2 and 411.7.3 are applied for a nominal voltage not exceeding 50 V ac or 120 V dc then this combination is known as FELV.
Does that mean then that if and installation is defined as FELV then it IS protected...
Hi, I would be very grateful for any basic wiring advice anyone could provide for a hi-lo pir security light if possible. I believe I need to put the one of the switched live cables into the section marked 1 along with the other main live wires and the other switched live into the section marked...
Hey all
I am suffering with 'engineers no good' syndrome.
My engineers are installing intruder and cctv systems, and know the tech side of it fine.
But, having never done an apprenticeship or site time, they just lack the basic skills of how to install cabling etc.
I have been out to site (I am...
Hello all -
I'm new here - signed up to try and answer a really basic electrical question which I have googled in vain.
I just bought a mechanical doorbell which runs on mains power - which I presumed meant that it would have a plug on it, or at least a socket for a plug cable. But in fact...
Hi all,
Just wondering if I could grab a hand understanding this circuit, or more specifically what each individual part is/what it does?
Thanks for the help
Hi,
Last year i had an office built in my garden and a 10mm SWA was laid between the main consumer unit in the house and that in the office. I have 2 sheds about 40m from the office & 15m apart and i'll like 3 double sockets in 1 and 1 light fitting and a double in the other and 1 light...
An old small tubular striplight in a desk/cubby hole in my aged parents' house has gone and it seemed silly to call out an electrician for one small light so I said I would help.
Obviously, I thought it was just the bulb but tried the bulb from the bedroom next door, which has exactly the same...
Good day all.
I was wondering how you actually go about using a megger to test the quality of insulation of a motor, I understand why you would do the test. If you were to test it at the motor starter and you have isolated the circuit would you need to disconnect the wires going to the motor...
Hi,
I'm a new member but I run a commercial electrical contractors, it's a family business around for 35 years and I've been in it for about 13 now. Started off in admin, then a full apprenticeship, electrician, junior project manager, estimator, manager, now I'm operations manager running all...
Hi, I have managed to get a work trial next week for an electrical firm as an electrical improver (have completed my level2/3 2365 after 3 years of night college at huge expense....on a student loan), and I was wondering if anyone had any hints, tips etc.
I was totally honest and told the...
Sorry if this has been covered before but i cant get the search to run on only this section, its just a very simple question. I am putting in power for a TV in a bedroom, and am going to try and help the young couple concerned as I know they are a bit hard up, by doing the aerial bit as well...
Hi,
I've signed up to these forums hoping to get a little help with a basic understanding of electronics.
I have two daughters age 9 who were bored last weekend, so I went to my local electrical shop and purchased a random basic beginners Electrical kit as the shop keeper thought suitable. I...
I'm just look for confirmation thoughts on this first point.
I think when IR testing on an existing installation and it’s not practical to remove all vulnerable equipment. I can connect L to N to earth and test at 500V on the circuit I’m testing.
The question is if I do the above...
Newbie here so go easy please!
Am working on a new build that will be more high end then im used too! they are having the touch screen control panels in each room to control lights, heating & whatever else they choose (believe they are using Phillips dynalite range)
The spec, cables etc is...
I'm nearly 30 and not an electrician but I thought you guys would be the ideal people to answer this.
Where are good place(s) to get high quality basic tools?
I bought some cheap screwdrivers a few years ago and they ground down really fast when trying to undo screws that were tough.
I am...
Hi guys,
I am just doing a basic spur after doing a fair bit of reading on it - would be grateful for an opinion.
I have gathered all the bits I need for putting in a down flow heater above the door in my bathroom upstairs, it will be in an "outside zone".
The kit I think I need:
Down flow...
Hello can anyone direct me to how to do basic wiring such as radial and ring main circuits on how to do it and how it works please I have tried to look everywhere I just want to know how it works like where is it wired into from the consumer unit what connection do u wire into? And how does it...
Hey all, fairly new to this so bare with me,
i have an interview this week and Iam expecting a skills test does anyone have any idea what I could be facing? Or what you have experienced, the job is in a food processing factory.
ive heard rumours of having the wire a dol with pilz relay?
not...
just want to clear a few things up:
intend to use a generator on a domestic using a manual change over switch (basically if the electricity goes off)
my questions:
1) if generator has floating earth (neutral and earth not connected together), can i rod/spike the generator frame and connect...
hi
basically we have a small commercial kitchen, we have an open hood/ canopy (approx 1.5m wide), no filters or anything within it (above the gas hobs), then a solid duct goes around 3m up through 1st floor and fan on top of roof (type where fan is directly on top of duct),
The fan is working -...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc