before

  1. D

    Anyone tried these before..?

    https://www.screwfix.com/p/knipex-5-in-1-vde-electrical-installation-pliers-8-200mm/5211f 40th Birthday coming up and my parents are insisting they get me something so might cut a new pair of cutters / shears and wondered about these
    • Dustydazzler
    • Thread
    • anyone before these tried
    • Replies: 10
    • Forum: UK Electrical Forum
  2. J

    Switch before or after transformer?

    Hello- I'm planning to install a bunch of LED lights in my kitchen cabinets. The idea is to have a small LED strip turn on automatically when opening the cabinet door. I've found a 12v LED strip that can be cut into 30cm long sections that will be perfect for my application, along with some...
  3. J

    2391 before completing my NVQ L3?

    Hiya fella's, I have almost completed my NVQ L3 (with the final 10% completed via employment) and I have been working as a sparks mate for the last 3 months on-site. I have so far gained experience in emergency lighting, most containment, installing industrial safe isolation boards (with them...
  4. Charlie_

    Something I haven’t seen before

    Any ideas what this is? And how it works?
  5. PJH2903

    Megger 1730 calibrate or not before sale?

    I have an MFT1730 which I will be selling (have upgraded) and would value the groups opinion. The calibration certificate has expired so is it worth me spending the money to have it recalibrated before I sell it? What would you all pay for a meter that is in excellent condition calibrated v’s...
  6. Michael J

    Green neutral anybody seen this before?

    Haven’t seen this before
  7. L

    Fixing cables before dot and dab

    Hi guys, Doing a kitchen refurb and adding and extending some sockets and extending the cooker circuit. Builder is going to dot and dab the walls next week just getting people’s opinions on the best method for fixing cables. Clipped direct to the wall or in oval tube or capped? Also 25mm or...
  8. S

    Sometimes you have to laugh before you cry

    Got a call from a beauty salon to ask if I repair electronic beds. I said no but the very camp voice begged me and told me no one would repair it apart from the German makers - and they wanted a fortune. He badgered me until I said I would come have a look. I've never been in such a place like...
  9. gjcone44

    zs readings before and after rcd.

    anyone come across this before zs at board 0.28. then when measure zs on rcd side on live and neutral, reading of 0.77. from the same earth position.?, ie got a socket a meter away from board earth loop 0.81. measure earth from socket to board its 0.02.
  10. Marcus Vaughan

    Anyone seen this symbol before?

    Logo in the bottom right corner - looks like I shouldn’t be installing them in a home. Also - 30 of them needed per lamp at 15w each - two lights (one already installed by customer) + other lights. It’s right up close to maximum demand - even with diversity..... Customer supplied lamps - time...
  11. Richard Cook

    Dishwasher needing switched off at wall to ‘reset’ before each cycle?

    I’ve got a dishwasher from IKEA (integrated into unit) and it’s under 2 years old. For the best part of since I’ve had it... when I go to turn it on it will beep (as if it’s picking up on the pressing) but it won’t show anything on the display etc. I have to switch it off at the wall and wait...
  12. D

    12v garden lighting help before i start!

    Hi i'm looking for some guidance on a garden lighting project before i start. I'm hoping to install a sets of 12v led lawn lights [5 lights, 5w each], with a potential cable length of 50+ meters. Is 3183P 0.75mm rubber cable sufficient for this length of run [50+m]? What cable size would you...
  13. G

    Circuit Breaker drops before Fuse

    I have underfloor heating rated at 3kW. The circuit goes through a fused switch with a 13A fuse in it. That is supplied directly from the main fuse box with a B16 circuit breaker dedicated to that circuit alone. Every time we use the system, it warms up for a bit, then the circuit breaker goes...
  14. Steve93

    Help! Never seen this before!

    I am installing solar to a house and this is there main incoming. I can’t see an Earth anywhere but test ZS across L-N coming out at 0.20. Then with gas bond disconnected is 0.38! But we only have gas bonding. No other earth anywhere. Anyone had this?
  15. telectrix

    calculation check before i rip the flat to bits.

    hi folks, got a CU change to do. flat rewired circa '70's. wylex 3036 fuses. my concern is earthing conductors. at present they are 6.0mm. TN-S. Pefc is 700A. not sure of main fuse size, so have taken worst scenario at 100A. referring to tables, @ 700A the disconnect time for a 100A BS1361 is...
  16. T

    Re suspended ceilings thread and the mess in it, before and after

    Just a little update as @marconi expressed it may be interesting to see before and after on sargasso sea of cables above ceiling.
    • The Ghost
    • Thread
    • after before ceilings suspended thread
    • Replies: 43
    • Forum: UK Electrical Forum
  17. Dave OCD

    Before and after some 'unbodging'.

    I've been doing quite a lot of work in a nice house for the last 3 days, bought by a retired lady and her son last Autumn and I was recommended after they'd had a N####C A/C in a few months ago. The biggest job was lowering the C/U to a sensible accessible height, the previous 'Electrician' has...
  18. Z

    Insulation Test before consumer change.

    Guys Is it good practice to zap the old wiring with a 500 volt insulation test before any consumer unit is installed? Or do you just go ahead and rip out the old one and fit the new? Zippy Trainee Sparky
  19. S

    1ph DB Piggy backed off 3ph DB Before Isolator. - EICR

    Hi Guys, This is the second time I've come across this on an EICR, but with slightly different circumstances. It has made me ponder if my previous code, and if my current idea for coding is correct or not. Basically someone has bodged an extra single phase supply off the incomer side of a 3...
  20. C

    VYTEC Fuse board never seen before

    Hello People Has anyone Came across a VYTEC board before and successfully installed a more easy to come by brand of MCB asides fro VYTEC? I have been told its a rebadged GEC apparently
Best EV Chargers
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top