I was working in an old shop yesterday in which I have been asked to do an inspection. While there I found cables draped diagonally across the ceiling of the cellar. The unprotected choclate block is clearly a Cat 1, but what would your reaction be to the cabling?
most new light fitings now seem to come with the connector block within a square enclosure or choc block. Had to fit a replacement bathroom light yesterday circular bulkhead (g9 bulb). there did not appear to be enough room for the choc block to fit. i removed the choc block and fitted wago...
i've got to replace a board, it's in a stupid location (behind a garage door frame) and wants moved about 4 foot to the left. half of the circuits come throught the back of the board along with the tails and the other half are clipped to the black wall and go up.
ideally i want an enclosure...
As many of you know, I'm not an electrician so please go easy on me.
Do a PV on a new build etc. Customer told me the electrical connection was going in so we were good to go.
Turned up yesterday and all he has is a builders supply and wants us to tee into that. The is a consumer unit up but...
Hello Everyone,
New here - Im not a Spam! but nice to be in here, read a bit from outside: Verdict - worth joining!
I'm not yet a spark but planning on steps to become one and hope I will find a lot of encouraging support here
Thanks and take care
Jon
Hello,
Would anybody be kind enough to point me in the right direction on how I would energise this roller shutter
door motor to go one way or the other so I can start to design a control?
Thank you in advance for your help.
beefburger
Thread
block
door
electricians' talk
motor
phase
shutter
single
single phase
terminal
terminal block
wiring
Hi,
Anyone have any idea on this one.
Have a customer that lives in a block of flats, they're all owned and want to install a PV system on the roof.
Have said best to tie it into the communal areas electricity meter etc but bit stumped on the EPC.
There is no heating in the communal areas...
Hi,
I'v got a job to do which involves putting 1 set into a length of galv conduit. I don't really get the chance to do any Galv as such, and don't have a proper bending machine. Could anyone advise as to whether a plumbers pipe bender would do the same job? or any other suggestions greatly...
Hi quick one if you come across the meter tails coming from the meter to a henley block then from henley block to main switch on consumer board, if you replaced that consumer board would you still need to remove main fuse or could you just disconnect from henley block and leave fuse intact...
hutch6447
Thread
between
block
electricians' talk
henley
main
main switch
meter
switch
times
We are quoting for a 4kw system on a block of flats, going into the landlord's supply so the residents will not benefit. There is no heating in the communal areas, just lighting for the stairs - any ideas on EPC??
Hi everyone! I've had a browse on the net and on this forum but can't find any information on the photo attached
Young ladys flat in a block of apartments, this is the only telephone point that's wired up and it works perfectly with telephone and router plugged in.
Problem is, I've never...
Evening chaps a periodic today walked through the front door and my concerns were were raised just glancing at the supply cable and cut out and yes my concerns were right ,and obviousley the electrical contractor never tested the supply infact the installation as this would have thrown up the...
nickblake
Thread
attach
block
connected
dno
earth
electricians' talk
house
test
Hi all, looking to install a jacuzzi for a friend of mine, but his fuse board doesnt have any room left, so was thinking of cutting into the main cable leading to the fuse box with a henley block, then running a 10mm cable to a 63amp rcd, question is what type of cable should i use? as...
Done a board change this week and discovered the house has no earth(except for the 0.51ohms of the Gas!), all the earths go to the block on the side of the head but there's 0v between the block and Iine, I got the DNO out who said there has never been an earth since the head change 15 years ago...
LlandrilloSpark
Thread
aus
block
certificate
change
dno
earth
electricians' talk
installation
supply
a dude has just rang me and says the lights are staying on continuosly... i think could just be jammed... anything you'd like to advise me before i go have a look... i have never looked at these before and i said probably just need replaced.. he sqid if thats what it takes
Hello,
Couple of questions, firstly does each flat require it's own dedicated earth to the main incoming on the ground floor of the property, zs readings are fine with the 10mm 3 core SWA that has been used. (never certed a block of flats before, jus wanted to be 100%)
And, there is a...
hi, hola, bonjour! This is my 1st post ever on any forum or indeed on the www! I have recently finished a 2 year college course on electrical installation and testing (city & guilds 2330-2331) and am now trying to find my way in the slightly daunting world of domestic installation in the hope of...
What's the best way to wire an FCU that fed an old immersion heater now disconnected to power a light that is to be fitted in a cupboard upstairs. The FCU is halfway in the cupboard so a bit far to use a switched fcu for the downlight so I need to connect a switch near the door. Would this be...
Simon_
Thread
aus
best
best way
block
connector
cupboard
downlight
electricians' talk
fcu
light
neutral
switch
wire
I know that it is wrong to just use a connector block and tape it up. However, I really can't find the reg / regs that state this.
Can anyone point me in the wright direction?
I like to know exactly why Im doing what Im doing.
Cheers
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc