I have following air circuit breakers for sale used only 1 time for a project
Brand - SOSUL
MFGD - 2011.11.17
Origin - KOREA
Rating - 630A
Model - VL - 12E20B06
Brand - ABB
MFGD - 2009
Origin - Italy
Rating - 630A
Model -
Brand - ELATEC
MFGD - 1999
Origin - German
Rating - 800A
Model -...
Hey moving out in few month, selling all my stuff. So i have twin and earth 1.5/2.5 like 200-300 meters each, 3 core few hundred.
Rcbos B6/16/20/32/40 amps. And like 100 or more old circuit breakers and rcb. Aswell some mains I think, earthing 10/16 mm/ bars sockets switches and etc.
I can sell...
Hi
I'm a Plumber and heating engineer and a new member to your forum.
I have a basic knowledge of electrics but I'm curious about how breakers and Rcd's work and whether they prevent fires.
My basic understanding is the breaker trips if more power is been drawn than is safe and an RCD...
Hi guys,
Hoping someone would be able to help with this one.
My grans house still has the good old fuse box with fuse wire which I am aware could do with upgrading to a proper circuit breaker panel.
However I have no idea on how much it would cost her and hoping someone would be able to give...
We just had a range oven fitted (gas on hob with two electric ovens - total power rated at 5.3Kw) so a 32Amp mcb is in the board on the dedicated cooker circuit which was there from previous cooker. When one oven is on everything works fine, but when both ovens are switched on together they trip...
Afternoon all
Hopefully someone can throw some light on a small problem i have.
I am currently on a job, carrying out an eicr on a building and i am confused by the ocpd feeding it......
The set up is, main cut out in the sports hall building, then there are 5 circuits fed from the 200a main...
Morning fellas
On job at moment. Am just looking at lighting circuits. They are supplied off 20A type C breakers run in 2.5mm to MDB's then from there each lighting circuit goes down to 1.5mm flex 5 core with 2 cores being used for dali. From what I see cable rating is 20A is a 20A breaker to...
Was just looking at circuit breaker types and I was a little bit confused so wondered if anyone could help clear it up.
Basically say If I determined my current would be 26a before taking into account any rating factors and chosen a 32a circuit breaker for my protective device. After taking...
I'm thinking of having a new fuseboard fitted. The existing one has 8 fuse in it and is boxed in. The 2 electricians who have come to quotesay i need a board with A main switch 2 Rcds and 8 circuit breakers. the board will not fit in the boxing. My friend has a board with 1Rcd and eight circuit...
help!
I've just tried doing what I thought was a simple replacement of a plug fascia as the old one got covered in paint during some decorating. Turned off the power at the breaker, ensured the circuits were dead, removed the old plug front, wired in the new plug and replaced the fascia back...
Hi folks,
Well today I attended another house to perform a bathroom upgrade. Upon visiting the mains board I noticed it was a MEM. Not ideal I thought as my previous experience taught me that RCBOs were not possible with these mcbs. I then noticed that a previous spark had fitted a hager RCBO...
Hi
I am replacing 2 circuit breakers in a Schneider panel board. Board is 3 phase and main switch is Schneider NSX 100. Circuit breakers are Schneider NS100N compact series. Replacing 30 amp breakers with 63 amp identical units. The breakers are single phase units.
my problem is that I am having...
Hello,
I have a problem with design current (Ib) and selection of the circuit breaker (In).
If I have a circuit of 7A and I apply no diversity, then Ib = 7A and I select a 10A circuit breaker.
But if I apply diversity and I get, say, 5A, is 5A now the design current Ib? So can I select a 6A...
Alessandro
Thread
breaker
breakers
circuit
circuit breakers
current
design
Hi
I'm hoping that someone can help.
I am adapting some circuits which are supplied via an in line ups. At present, the ups supplies a 72 way db and the final circuits are supplied from the DB. This is a laboratory research environment and it is expensive (about £20k a time) when they...
The heading of table 41.3 says it shows " max earth fault loop impedance Zs for Circuits Breakers..... giving compliance with 0.4s disconnnect time of 411.3.2.2 and 5s disconnnect time of 411.3.2.3."
411.3.2.2 is for final circuits not exceeding 32A. 411.3.2.3 is for distribution circuits and...
So an old colleague of mine stipulates that ring main should be protected by 20 amp breakers. Why you ask?
Well he said because a piece of 2.5mm2 can only take circa 26 amps and if the ring main broke at any point it would effectively make it two radials, and it would be protected by a 32 amp...
Who makes a TP+N panel, bigger than a consumer unit, for example, 14-way (with space for 12 or 14 three-phase breakers).
It should feed its outgoing breakers using bus bars, not wires.
(I call this a Type B panel)
And it should be usable for Dual RCDs, one for the left side of the panel and one...
im a 1st year apprentice thats why im asking this question, from what ive gathered the higher the current it takes to trip as in 10 times the rated current etc... for that you need a lower zs than if it was a b type why is that?
my thoughts on it is that becuase you have a higher current so...
Jake1579
Thread
breaker
breakers
circuit
current
higher
lower
times
type
Hello guys, hope someone can help me with this.
i was carrying out a small job on a ring main (re-fix a socket to a wall nothing major), and noticed that the ring was being supplied from more than one circuit breaker a long with the other ring main in the flat. Obviously i rectified the job as...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc