broken | Page 4

broken

Recent contents View information Top users
  1. B

    Single cu change Bonding cable to gas then water broken

    Hi people, I'm due to do a cu change and noticed the single bonding cable to gas then to water but it's in two bits of cable. Am I right in thinking that it have to correct this due to cu change? It would mean running another cable which is annoying as gas and water are about 18inches apart but...
  2. infinity

    Megger broken help!!

    I pulled the black lead out my 1553 today and the whole connection came with it! So basically I don't have a tester, any ideas on who I can send it too to have it repaired at a fair price? Ideally with a quick turnaround!
  3. J

    Broken CPC, done all I can but still no luck.

    I've been let loose today to do a PIR, EICR, E, I,E,I, O what ever they wanna call them these days in an empty flat and have an annoying CPC broken in RFC. 2 bed flat 3 way CU - Cooker (30), Lights (6) and RFC(30) End to end of r1 and rn fine but r2 is broken. This is what I did- connected...
  4. M

    1960s electric underfloor heating - broken?

    I have just moved into a 3 bed end-of-terrace built in 1969 that was supposed to have still-functional electric underfloor heating in the concrete. An electrician said it wasn't working and disconnected it (removed the thermostats and cut the cables running to the consumer unit, even though I...
  5. C

    Outside socket and broken MCB for Spa Bath

    Hi I'm new here and I'm not an electrician but I came across this place when searching for answers to my problems. I have just moved into a house that was re-wired in 2006. There is a 2 way outside socket that has broken so I am looking to replace it and want to make sure I get the right...
  6. P

    least likely van to be broken into

    Hi guys about to buy a new vehicle as my estate has just about had it. Don't really need a van so was thinking of something like Nissan Navara. My question is from your experiences is a flat bed truck type vehicle less likely to be broken into than a van. I'm based in rural Suffolk. Cheers for...
  7. M

    Fixing a Broken Alarm

    Yesterday morning the alarm in my house went off without reason, despite entering the code we couldn't get it to stop so my housemate (who had an interview later that day), pulled the panel out of the wall. This stopped the alarm but now we need to reattach it. There are 7 wires, the red, blue...
  8. B

    Belfast- downlighters broken - bulbs checked & fine - transformer or dimmer at fault?

    Hello folks, First post so apologies if im sounding thick. 7 downlighters in our hall. Replaced two bulbs two days ago. Yesterday turned them on and they flashed off immediately. Checked consumer unit and nothing wrong. Checked bulbs this morning in another light and they are all...
  9. C

    3 months old 4-Nocks Power Reducer broken - who's responsible for fixing?

    Mid November our solar panel fitters purchased an Elios4you system from Greenologic, with a Power Reducer to heat the water, and fitted this for us with solar panels. On 13th February the Power Reducer started to take electricity from the grid instead of from the solar panels. We had to switch...
  10. HappyHippyDad

    Gas and water bonded together with a broken conductor?

    Evening everyone.. I have just undertaken an EICR and there is 6mm bonding to both water and gas at the correct points (within 600mm of entering building), however they must be joined somewhere as there is only one 6mm in the CU. I believe this would be ok if the conductor was unbroken but...
  11. S

    Broken CPC on ring final

    My friends downstairs sockets are tripping the RCD. First thing I did is unplug everything on the circuit, switched on the MCB and the RCD tripped. Tested continuity of L-L N-N CPC-CPC between the legs. CPC has no continuity whatsoever. Could anyone advise me what would be my next step to...
  12. M

    no earth at socket

    in the picture theres no earth at the socket above the worktop, the earth is broken from the JB to the socket somewhere and is not accessable. can I run a single earth between the two sockets.its a 20 amp radial cct.
  13. H

    broken ring .

    broken ring , no continuity on all conductors , whats best way to find the fault?
  14. M

    Method statement & risk assesment for removing a broken module

    Hi, I was wondering if anyone could share their knowledge in removing a module that is surrounded by many others on a roof. There is adequate roof access & mansafe points to harness to but it was more the electrical safety issues relating to isolation & removing a row of panels to access the...
  15. D

    YODALARM YO8 240V is broken

    Hi all, I found a YODALARM YO8 from Clifford & Snell in my shed. But it's a little bit broken because it fell into a chimney (long story). The components are fine but some of them and a couple of wires are disconnected from the circuitboard. Now I am at sea, and don't know how to connect them...
  16. L

    Ive broken the front cover to the consumer unit

    HI guys Ive accidently broken the consumer unit in the empty property im working in at the moment. I took the cover off of the Memra 2000 Ad board having isolated all the breakers, rcd's and main switch then I took the main fuse out (yes Ive taken the main fuse out before with out doing so...
  17. T

    Eicr code - db is dirty

    Hi guys, Im doing an eicr on an events building, the db is in the main kitchen, however dirt and grime havegot into the db. Would you code it? Im thinking c3 as there is no sign of danger but improvements could be made. Or am i being too picky. The cause of the grime getting in is the fact...
  18. M

    broken megger

    Hi chaps don't know if this is the right place to post this here goes, whilst doing a test last wk dropped my megger 1552 and the case cracked,meter itself works fine was wondering if i could get a replacement case any help much appreciated
  19. R

    Inverter broken

    On my array, an inverter is broken. Nothing on the screen. (Sma) Sma are replacing it ASAP. I was just wondering how I should leave the circuit breakers AC or Dc? ( I guess it doesn't matter as I haven't been advised either way) For fact fans- 50kwp array.. ( Field mounted) 250w suntechs and 4...
  20. sparkymalarky

    Advantages and disadvantages of Ring Circuits

    Found this argument on the IET website and it made for interesting reading at work! http://www.------.org/resources/wiring-regulations/ringcir.cfm?type=zip

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top