check

  1. R

    Whilst doing a maitenance check

    Good morning guys I hope your all well. Since I got the first part of my 2391 done I've been having a rest from the studying because it was at points a little bit intense doing mock after mock after mock. Ill will soon be picking up where I left off and I will be indulging (at cost no doubt!)...
  2. J

    Switch Panel sense check

    Morning All! Looking for some one to sense check a wiring diagram I have made for a switch panel in my car. Ok so helpful information - All switches are 3 pin LED toggle switches. I would like them to light up when activated. The LEDs Circuit is currently in the car wired like they are in...
  3. L

    UK When replacing a board do you need to check every socket?

    Hi guys I recently had an electrical safety test and the electrician said he needs to replace the board because it's quite old. The electrical board and all other electrical stuff is outside of my house in the landing. My question is, when replacing the board, does the electrician have to come...
  4. J

    EICR check failed

    Hi Guys, Just had an EICR test and was told it will fail , but not too bad (a couple of C2s) but needs doing. Waiting for the failure cert. to show me the total work needed, and should be here tomorrow. Is there a kind soul out there who can assist me [a retired old electrician who's quite...
  5. S

    UK 13Amp plug check card Electrical Safety First wanted

    I've mislaid my 13Amp plug check card from Electrical Safety First, and they aren't sending out replacements at the minute. Can anyone help? (I'm obviously happy to pay!).
  6. D

    (UK) Sanity Check Kitchen Oven wiring spur

    Hello, I'm hoping someone who knows more than me can sanity check this wiring diagram for my Electric Oven, Extractor Fan and Gas Hob. Background: I bought a new oven, I thought the old one was plugged in with normal plug but it was actually hard wired and the extractor/hob were plugged in...
    • dande650
    • Thread
    • check diagram diy fuse kitchen oven overload spur wiring wiring help
    • Replies: 2
    • Forum: UK Electrical Forum
  7. S

    JCC FGLED6 batch check

    Anybody know where I can check if some fgled6 are part of the good ol bad batches? I've just done an EICR on a property and some numpty has put a JB above every light and 2 core flex into each (NIC domestic installer that has even certificated it!), they arent double insulated so all need re...
    • suffolkspark
    • Thread
    • check jcc
    • Replies: 5
    • Forum: Lighting Forum
  8. R

    Need a sanity check on a 3-way smart switch installation.

    Hi. I'm a newbie in this forum. I'm a homeowner who's done plenty of simple lighting, outlets, etc. even including a couple of circuit breakers. I've never done a 3-way switch before though, let alone a 3-way smart switch. I've been doing my homework, but would still like a sanity check. The...
  9. A

    Replacing Drayton Thermostat with Digital - Wiring Check

    My drayton thermostat (3-wire) stopped clicking so decided to buy a wifi digital thermostat. Digital thermostat dry contact is not wired to the live within the unit unlike the drayton. Can someone confirm my jumper cable position is correct? (i.e. does it matter which side of the dry contact...
  10. E

    Insulation resistance check on LED fittings

    Hi, Do I need to disconnect LED fluorescent fittings when doing an insulation resistance check? Thanks
    • Everzy28
    • Thread
    • check disconnect doing fittings fluorescent insulation insulation resistance led resistance
    • Replies: 2
    • Forum: Lighting Forum
  11. J

    Omnik Inverter throwing Relay Check Fail Fault

    Have a fault reading; Relay check fail. Done some research and replaced the x2 check relays with quality components. Still have the same fault sadly. Any thoughts ?
  12. Lister1987

    Check Understanding; Minimum alarm requirements for private rent sector

    Just want someone to sanity check me here; my understanding is that battery powered detectors are not permitted in the private rent sector - they're fine if you own/live in the property yourself but the minute it becomes private rent then the minimum requirement is LD3 - Mains Powered (with or...
  13. S

    How to check voltage on heat press.

    My heat press stopped working and have been quoted £130 for a new control board but obviously they can't be sure this is the issue. How do I check that the press is receiving power. I have a multimeter available but its knowing where to take the readings. I have changed the fuse and cable...
  14. Vortigern

    Electrician Jobs Portsmouth spark needed to check electric boiler out

    Ex has flat in portsmouth with electric boiler. Packed in quoted 3k for replacement. Need someone to check element to see if it needs replacement rather than replace whole boiler. Anyone up for that?
  15. R

    UK Please check my logic for upgrade lights project wiring!

    Hi all, I have some outdoor lights, and I want to update the circuit to add a bit more functionality. I have drawn a little picture of what I have now: When we walk past the Outdoor PIR sensor 1, all lights come on, and then go off. This works fine! Now the behaviour I want: Add another...
  16. A

    Asbestos check before fixed wire test

    Hello all. I'm starting to do more fixed wire testing at my company and wondering about asbestos checks. The last company I worked for (was an apprentice at the time) didn't check any asbestos register before starting the test so just wondering where to stand with it. These will be commercial...
  17. N

    Solar Health Check?

    Hi All, Looking for some advice, got a cold call today from someone who informed me the company who put up my panels have ceased trading. The new company is contacting their old customers and offering to help with any warranty issues. They need to do a health check to validate the system health...
  18. Lister1987

    Emergency Lighting - Check understanding

    Im toying with the idea of putting a maintained switched emergency light under the stairs as this is where the service head/DB is located and, in the event of a power failure I don't want to be rummaging around trying to find the torch that I know I left there but SWMBO since moved it without...
  19. R

    Insulation resistance check

    Hi - I have a Warm-up underfloor heating system. And it's stopped working. I did a basic resistance check - and clearly there's a problem (shows just 18ohms when it should be nearer 200). Warmup have said they can send an engineer around to lift a tile after doing a thermo heat check...
  20. Dan

    IMPORTANT: Quick forum permissions check - Can you reply to this if you see it please? :)

    IMPORTANT: Quick forum permissions check - Can you reply to this if you see it please? :) I've reconfigured the forum permissions and usergroup settings and need to make sure that those who should have access to here, do actually have access to here. So if you can reply to this if you see it...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top