Hi,
I’ve been asked to look at a ADE optima compact plus as the zone 1 light is activating and it beeps everytime the PIR as activated I.e when someone walks Infront of it even when the system isn’t armed? You can press reset and the light goes off but as soon as it activates again it comes...
Hi Guys I have an old room stat which is located upstairs in the hallway that I wanted to replace with the Salus RT510RF so I can take it from room to room. I was hoping to just swap it over but I think I will need to run additional cables, if that's the case I might as well just run a standard...
Hi have an Optima Compact alarm panel, when I set it just keeps beeping, if I set It and open and close the front door it sets, but if I open the front door as if coming home, the alarm goes off straight away. No 1 zone is the timed zone, so I have it in the right connection. Very grateful for...
Good Morning,
Was wondering if anyone can help me out. I am looking for the following type of circuit breaker for a customer of ours. Have looked into modern replacements but can't find any suitable ones so it's looking more likely that we need a direct replacement.
What we are after is the...
Hi,
I am looking for a panel to replace a 20 year old System Four alarm panel, the simpler the better and has to have integral PSU and key pad. What would the group suggest?
Thanks
I have a CTec Sigtel Compact panel with two stainless steel outstations. All in working order. Used but in very good condition. The handset has some minor UV damage so the cable is slightly faded.
Offers welcome.
NW Area
Hi Everyone
I hope you can help me on this issue. I installed the above panel in my partners house and it has been working fine for 8 months until last night.
She tried to set the system rom rkp and it just goes to unset on the LCD Display then back to day date and time display On the panel...
I am selling a complete Allen Bradley Compact Logix L32E plc,
All the of parts are as followed:
1x 1769-L32E Logix 5332E Processor Unit
3x 1769-IQ32 32 pt. Input Module
1x 1769-PA2 Power Supply
2x 1769-OB32 32 PT. 20.4-26.4VDC Sourcing Output Module
2x 1769-IF8 8 Channel Analog Input Module
1x...
Hi.
Does anyone have any experience of repairing or having this type of drill repaired?
I have been asked to investigate a problem of the drill stopping intermittently during operation.
It seems it could be a simple loose internal connection or a problem with the electronics.
I am loathe at...
Ok people, we all know what it's like like working within a limited suspended ceiling void and trying to angle your drill to where you need to be. I am currently using a Panasonic SDS to do do the job which is quite compact but coming to the end of its life. My major tools are all makita but...
The above trunking been specified on a job in a science room,what a complete nightmare,just wondering if you guys have come across it.You can't use the main central carrier,only the outside compartment ,usually for data.My problem is,cables,2 rings & lighting cables,it's a tight fit,kind of...
All used and removed from a working installation due for upgrade, as followed by X quantity.
Merlin Gerin Multi9 C32 RCD/MCB RCBO x3
Merlin Gerin Compact C101N 63A 3 Phase MCCB x5
Merlin Gerin Compact C101N 40A 3 Phase MCCB x1
Merlin Gerin Multi9 10A Type3 MCB x1
Eaton MEM AD16B B16 MCB x1...
Hi All, New to this forum and I've been looking around to find some information about my alarm. I've lived in my house for 6 years and I've never had any problems with my alarm, but over the weekend I had a power cut during the night. I think the alarm went off, but in the morning the power...
Had some rcbo's to retrofit to some dorman smith 3 phase db's earlier and it occurred to me as I was fighting past the other cables in the 72 way board that they are actually a nightmare to fit in a busy as heck board. Why they so bloody long?!?!
Good evening Gentleman.
I have had a small job in the pipeline for a while for a customer who is having stainless steel bollard lighting down either side of their drive way.
Nipped up to check on the jobs progress to find the client couldn't find the correct size light fitting so he has...
Hi. I've tried to fit an Optima Compact alarm panel with built in key pad. Upon energising there is a tamper fault. I've removed all zones & linked them out but still no joy. This is the reason I hate doing alarms & will avoid in the future! Any ideas please??:devil:
Hi, im hoping someone can help me. i purchased my house around 2 months ago and on the day of moving in and turning the electricity on, the alarm immediately went off! i pulled out the fuse which didnt help so i took off the front cover and disconnected the battery! ive since reconnected the...
Hi guys,
After a bit of advice please. Looking to change from an onboard timeclock to a Danfoss FP715 Si programmer (I realise this is a two channel whene only one channel is required, but it's what the customer purchased.
Now it's only a four wire connection from the boiler to the onboard...
Hello
I've got over a thousand 9w b22 cap CFL lamps that I want to get rid of, all brand new in original packaging, happy to sell them in quantities of 100 if you supply these to customers grab a rare opportunity to buy some cheaper than the wholesaler can supply and make a few extra quid, all...
Hi guys,
I have just bought this SDS drill from Bosch. Anybody else tryed this?
It looks shockingly week to me! 5.5 in concrete is a massive strugle. Or is my drill factory faulty?
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc