connection

  1. M

    Heating element connection

    Hi have been asked to fix connection on 3 phase printing machine the cable has disconnected for poor connection where cable grab been pressed obviously its not soldered, are there some high temp solder kits available?
  2. R

    BG Connection Concerns.

    Hi there folks, Daughter asked me to fit new BG light switches. The new type have changed their connections similar to LAP type. Now you HAVE to double over connections to ensure good connections otherwise if using several wires in connection some can pull out. The connection is bigger than...
  3. R

    New extension - 2nd fuse box connection

    Hi, We are building a new extension which is the opposite side of the property to where the current mains in and fuse box is located ( which are on the opposite side of an external wall ). The extension will be a new kitchen with an electric oven and hob, utility room with washing machine /...
  4. G

    C1 + Accessories Connection, what is it for when connecting to a head unit. ignition?

    In my c1 handbook connection A4 is (+) Accessories. What is it for? Ignition? Thankyou!
  5. M

    Touring Caravan dno connection

    Hi there im after some advice, I’m thinking of creating a 5 pitch touring caravan site 32 amps per pitch can use a standard 100 amp supply single phase from my dno. I need to tell my contact at western Power Distribution how big a supply I need. Can anyone help.
  6. C

    Three phase - serial connection

    I have two FCU's in the same room. Can these two FCU's (3 phase) be fed from same cable from the panel located in the another room? Is it acceptable as per codes? or do I need to run separate cables?
  7. S

    Issue with cat 6 connection

    Hey guys I installed a cat 6 ftp cable last week around 50metres. It goes from one cat6 faceplate to another. When I originally tested the connection it was fine with my network tester,we tested with a couple of cat 5e patch leads to check connectivity and was fine. Today the customer has...
  8. B

    Connection behind bathroom mirror?

    Hi everyone. Could someone please explain how an LED bathroom mirror with shaver socket should be connected to the mains? My interpretation of the regs is that a fused spur must be outside the zones. However, can the flex be connected in the void behind the mirror and by what means? I am not...
  9. pirate

    Telephone wiring connection help, please!

    Hello all, probably not the right forum but here goes anyway. My house phone wiring has become scrambled. I have the usual incomer with the screw-on plug - in faceplate, and 3 other sockets in the house, which have been unused for ages. Some months ago I had problems with my internet, so...
  10. D

    Replacement Oven & Hob on same 32 amp connection

    Hoping to get some advice as i like to understand what work will be carried out and what actually needs doing etc. Looking at replacing the hob & oven as they are on their way out and in my research I've found out the following. Oven & hob are both connected to an isolating switch just above...
  11. B

    Fused connection unit

    2 Questions, 1. 2.5mm T+E on radial, 20A breaker feeding 1 FCU that feeds water heater, can I come off this FCU with another FCU to feed a heater? 2. 2.5mm ring main, consisting off FCU and sockets all on ring, can I come off one of these FCU to feed a FCU spur?
  12. F

    Question about electrical connection and feasibility

    Hi, In the past, my flat had 2 beepers , 1 at the door, and 1 at the study much further away. In recent years, the evil housing association which owns the building has introduced new beepers/buzzers, but this time only 1 for each flat. Now, I find that, with just 1 buzzer/beeper, I cannot hear...
  13. D

    UF controller connection to boiler

    Hi All, I have a wundafloor 3 zone uf heating system and a separate rad system running off a Baxi Ecoblue Advance heat Boiler and Megaflo tank. The rad system runs fine via a Danfoss controller but the installer has not wired the uf controller to the boiler so the uf cannot "call" for heat and...
  14. Gavin John Hyde

    Do you all use cooker connection plates?

    Asked to connect a cooker up today, it is to an existing install, removed temporarily to allow new base units to be fitted. Connected it back up. however it was connected direct to isolator switch. no connection plate on the wall. cable comes down in wall, then out behind cupboard and then...
  15. IBRAHIM HAMEED

    Earth Leakage Relay connection with normal CT

    Hi Can I connect normal Current Transformers (CT) instead of Core Balance Current Transformers (CBCT) to Earth Leakage Relay.. Thanks
  16. A

    Shower overheating no loose connection

    Hi all. Shower has melted on top left corner. I thought it would likely be a loose connections on the feed. On taking the cover off the 10mm coming in and connector block looks fine and is tight and I soon realised the burn Mark is from the live going from the block up to the top of the...
  17. B

    Cooker connection to 13A socket

    I am in the process of buying a new Bosch Serie 4 HBS534BS0B. Total connected load electric: 2.99 KW. AO who I am buying it from state that it can be connected to a 13A socket other seller are saying it is 13 Amp (Requires hardwiring to a fused spur). There is a 13A socket already there that...
  18. S

    Neutral connection to heating programmer

    gas engineer can't fit new heating programmer as I need a neutral connection on the back plate. Advised to get an electrician. How much would this cost or would it be better getting a new heating system?
    • Susan Gillespie
    • Thread
    • connection heating neutral programmer
    • Replies: 7
    • Forum: UK Electrical Forum
  19. P

    Non-Electrician: Switch Fused Connection Unit Light Not Working

    The neon light on my flat-plate/switched fused connection unit doesn't come on when I use the washing machine. The machine still works - but does the fact that the light doesn't come on mean something is wrong? Do I need to get an electrician in?
  20. N

    Baxi 600 electrical connection

    Howdy - first post and need some advice. Baxi 630 boiler To start with i am not qualified in anything and i know the wiring in the photo is from the 90s. Please bear with me.... We had a new boiler fitted a couple of weeks ago by a certified gas engineer. He was a sub of my builder. At the...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Back
Top